Getting Error while posting Stock by using the T-code MB1C

[#1]

Hi SAP Gurus,

Good Day!

I am facing an issue while posting the Stock using the T-code MB1C with Movement Type 561.

I am getting the below mentioned error.

Acct. 20510 for trans./event key BSX, postable directly

Message no. M7109

Diagnosis

The stock account determined automatically by the system is one that is directly postable. However, this stock posting can only be made to an automatically postable account.

Procedure

Contact your system administrator.

Once I got this error message, I checked in FS00 by entering the G/L Account and Company Code. I went to the tab Create/Bank/Interest. Chexk Box for "Post Automatically Only" was ticked. I removed the Tick and tried. But, there was the same issue. Then, I ticked the Check Box again.

Yesterday also, Same error had occured during some other transaction, but, I remember some stock posting itself. It worked out. But, I don't know why, it is not working today.

One more thing. When I tried to post the Stcok using the Movement 501, I am getting the Error with respect to Account Determination. But, we can not do the configuration settings in OBYC, as somebody else will do that. I have checked and confirmed that, Configuration for particular valuation class is missing in OBYC Screen.

Also, I am thinking that, my issue may be resolved, if the configuration is done.

So, I like to know, whether I should for Configuration in OBYC Screen. If this is done, will Movement Type 561 issue also gets resolved? Please advice.

Please do the needful, as soon as possible.

Waiting for the valuable comments and inputs from ypur side.

Thanks & Regards,

Srinivasa M.S

+91-7387702227

[Former Member]

Dear srinivasa,

Please not of a point that the whole thing is related to your material valuation.

That depends on the valuation area(always plant), valuation class(similar material types), valuation category(different types of category), valuation type(classification inside a category), material type and the movement type.

These things are again grouped in OBYC as valuation modifier, transaction key event and valuation class. For a successful posting in MM, the entire criteria must be satisfied.So kindly check all these criteria before you conclude on configuration.

Regards,

Vishnu Kumar S

[Former Member]

Hi SAP Gurus,

Thanks all for your valuable suggestions.

I have checked various parameters. It's fine.

But, I have a doubt.

Why Transaction Event Key BSX is not assigned to Movement Type 561 under Account Grouping?

Apart from that, I have observed that, all the G/L Accounts related to this Movement are categorized as STK (Stock Accounts) in Field Status Group field. I have observed this thing in FS00 Screen.

Actually, to go ahead with the execution, I found out some alternative route, where in I can skip this Transaction. I created aPurchase Order, did Goods Receipt through MIGO with reference to Purchase Order thereby adding the Material Stock in the Receiving Plant. Then, I interchanged the Supplying and Receiving Plants to avoid MB1C once again and went ahead with the execution. I finished the Delivery Process. Finally, I am in the stage, where I have to do Goods Receipt with reference to Outbound Delivery . After entering all the necessary Details, a System Message saying "Document is O.K" is getting displayed on the status bar of the screen. After that, when I click on the "Post" Button, I am getting the same error, that I got at the initial stage i.e., 

Acct. 20510 for trans./event key BSX, postable directly

Message no. M7109

Now, it is struck in between.

Finally, I like to know the reason behind this.

Please note that "Post Automatically only" Button in FS00 Screen for the required G/L Account - Company Code combination has been ticked.

Also, I checked and confirmed that, there is no assignment of Transaction Event Key BSX for the Movement Type 101. Most of the cases, I have seen that, BSX will not be maintained under Account Grouping for Movement Types. Please explain me the concept behind this.

Please come back with valuable comments and inputs with some new solution for resolving this issue.

Waiting for the kind response from all.

Thanks & Regards,

Srinivasa M.S

+91-7387702227