Inbound Idoc processing issues - Partner Profiles - error status 56

[#1]

Hello All,

I'm having a little difficulty posting an idoc coming from MDM. It's a CREMDM04 xml coming from an MDM system. It is getting mapped through PI and is being split into ADRMAS02 and CREMAS04 Idocs. The message is being passed through XI and being posted to the ECC system, but certain fields in the EDI_DC40 header table are not being populated correctly (i believe). I'm using nothing but standard mapping/material from the SAP Business Content for XI. After looking through the standard XSLTs i cannot find the field-to-field mapping where the fields below are being populated.

The RCVPOR value (SAP[SID]) is correct when i view it in SOAP Header, but does not appear in the remote system under the receiver port for the inbound idoc.

The RCVPRN value ([String Value]) is incorrect in the SOAP Header and does appear in the remote system under the receiver partner number for the inbound idoc. How is the RCVPRN value being populated?

SOAP Header in IDocOutbound tag

<SAP:RCVPOR>SAP[SID]</SAP:RCVPOR>

<SAP:RCVPRN>[String Value]</SAP:RCVPRN>

<SAP:RCVPRT>LS</SAP:RCVPRT>

I've been trying to trace down the string value for the RCVPRN, but i cannot find it anywhere. Perhaps i'm just overlooking it?

When i set the proper values (port = SAP<SIDofECC> and partner number = <LSnameof ECC>) using WE19 in the remote system then the partner profile is found and i'm left with different error to please specify an address group.

Any help is very much appreciated! 😄

[Former Member]

Hi Jason ,

Just check out if you have done the following steps most of us make minor mistake here ....... I think this would solve your problem

***********************************************************************************************************************

To Configure the IDOC SCENARIOS ,PROCEED AS FOLLOWS

***********************************************************************************************************************

STEP 1:ALE SETTINGS TO POST IDOC INTO SAP R/3

We need to do the following settings in XI

1) Create an RFC Destination to the Receiving System in transaction code (SM59)

a) Choose create

b) Specify the name of the RFC destination

c) Select connection type as 3 and save

d) In the technical settings tab enter the details SAP SID/URL and system number#

e) Enter the Gateway host as same details above SID/URL

f) Gateway service is 3300+system number#

g) In the Logon /Security tab, enter the client, user & Password details of Destination system

h) Test the connection and remote logon.Both should be succesful

****************************************************************

2) Create Port Using Transaction Code IDX1

**************************************************************

a) Select Create New button

b) Enter the port name as SAP+SID (The starting char should be SAP)

c) Enter the destination client

d) Enter the RFC Destination created in XI towards R/3

e) Save

*********************************************************************

3) Load Meta Data for IDOC Using transaction Using Transaction (IDX2)

**********************************************************************

a) Create new

b) IDOC Message Type

c) Enter port created in IDX1

**********************************************************************************************************************

SETTINGS IN SAP R/3

***********************************************************************************************************************

We need to do the following settings in R/3

Logon to Sap R/3 System

**********************************************************************

1) Create an RFC Destination to XI in transaction code (SM59)

***********************************************************************

a) Choose create

b) Specify the name of the RFC destination

c) Select connection type as 3 and save

d) In the technical settings tab enter the details SAP SID/URL and system number#

e) Enter the Gateway host as same details above SID/URL

f) Gateway service is 3300+system number#

g) In the Logon /Security tab, enter the client, user & Password details of Destination system

h) Test the connection and remote logon.Both must be succesful

***********************************************************************

2) Create communication Port for Idoc processing Using Transaction(We21)

***********************************************************************

a) First Select Transactional RFC and then click create button

b) Enter the destination port name as SAP+SID (The starting char should be SAP)

d) Enter the RFC Destination created in SAP R/3 towards other system.

e) Save

***********************************************************************

3) Create Partner Profile with Inbound Parameters (WE20)

***********************************************************************

a) Create New

b) Create the Partner no. name as same the logical system name of the destination system

c) Select Partner type LS

d) Enter details for Type: US/USER, Agent, and Lang

Then Save

e) Select Partner no. and LS which were create above

f) Now we have to give some Inbound Parameters.So click on ADD TO Create Inbound Parameter

g) Select Message type

h) Double click on Message Type and Then Enter the details for Message Type and Process Code.

I) save

*******************************************

4) In Transaction SALE, Create Logical System

*******************************************

a). Go to Basic Settings-> First Define logical systems

and then assign logical systems

b) Double click on Define the logical systems

c) Give data for your Logicaal System and Name

d) Now click on Save.Here one window may appear just click on Continue.Now the Logical System name is ready

e) Assign the logical system name to the client

do let me know if it helped

Edited by: Tom Jose on Feb 21, 2008 9:04 AM