standard program

[Former Member]

hai everyone,

can anyone please tell the standard programs for uploading data using call transaction for mm and sd.

thanks in advance

gopan.

[Former Member]

what do you mean call transaction mm sd ?

[Former Member]

what do you mean call transaction mm sd ?

[Former Member]

yes ,

the standard program to upload material data using call transaction.

thanks in advance

[Former Member]

you should write your own program with bdc recording. populate the BDC data and write your own code.

report ZTES_MATUP
       no standard page heading line-size 255.

include bdcrecx1.

parameters: dataset(132) lower case.
***    DO NOT CHANGE - the generated data section - DO NOT CHANGE    ***
*
*   If it is nessesary to change the data section use the rules:
*   1.) Each definition of a field exists of two lines
*   2.) The first line shows exactly the comment
*       '* data element: ' followed with the data element
*       which describes the field.
*       If you don't have a data element use the
*       comment without a data element name
*   3.) The second line shows the fieldname of the
*       structure, the fieldname must consist of
*       a fieldname and optional the character '_' and
*       three numbers and the field length in brackets
*   4.) Each field must be type C.
*
*** Generated data section with specific formatting - DO NOT CHANGE  ***
data: begin of record,
* data element: MTART
        MTART_001(004),
* data element: MATNR
        MATNR_002(018),
* data element: XFELD
        KZSEL_01_003(001),
* data element: XFELD
        KZSEL_02_004(001),
* data element: MAKTX
        MAKTX_005(040),
* data element: MEINS
        MEINS_006(003),
* data element: SPART
        SPART_007(002),
* data element: MAKTX
        MAKTX_008(040),
      end of record.

*** End generated data section ***

start-of-selection.

perform open_dataset using dataset.
perform open_group.

do.

read dataset dataset into record.
if sy-subrc <> 0. exit. endif.

perform bdc_dynpro      using 'SAPLMGMM' '0060'.
perform bdc_field       using 'BDC_CURSOR'
                              'RMMG1-AENNR'.
perform bdc_field       using 'BDC_OKCODE'
                              'AUSW'.
perform bdc_field       using 'RMMG1-MTART'
                              record-MTART_001.
perform bdc_field       using 'RMMG1-MATNR'
                              record-MATNR_002.
perform bdc_dynpro      using 'SAPLMGMM' '0070'.
perform bdc_field       using 'BDC_CURSOR'
                              'MSICHTAUSW-DYTXT(02)'.
perform bdc_field       using 'BDC_OKCODE'
                              '=ENTR'.
perform bdc_field       using 'MSICHTAUSW-KZSEL(01)'
                              record-KZSEL_01_003.
perform bdc_field       using 'MSICHTAUSW-KZSEL(02)'
                              record-KZSEL_02_004.
perform bdc_dynpro      using 'SAPLMGMM' '4004'.
perform bdc_field       using 'BDC_OKCODE'
                              '/00'.
perform bdc_field       using 'MAKT-MAKTX'
                              record-MAKTX_005.
perform bdc_field       using 'BDC_CURSOR'
                              'MARA-SPART'.
perform bdc_field       using 'MARA-MEINS'
                              record-MEINS_006.
perform bdc_field       using 'MARA-SPART'
                              record-SPART_007.
perform bdc_dynpro      using 'SAPLMGMM' '4004'.
perform bdc_field       using 'BDC_OKCODE'
                              '/00'.
perform bdc_field       using 'BDC_CURSOR'
                              'MAKT-MAKTX'.
perform bdc_field       using 'MAKT-MAKTX'
                              record-MAKTX_008.
perform bdc_dynpro      using 'SAPLSPO1' '0300'.
perform bdc_field       using 'BDC_OKCODE'
                              '=YES'.
perform bdc_transaction using 'MM01'.

enddo.

perform close_group.
perform close_dataset using dataset.

regards

vijay

[Former Member]

hi,

for materal creation this is the direct input program <b>RMDATIND</b>

but in SD what do you want..

Regards

Vijay

[Former Member]

RMDATIND IS STANDARD PROGRAM FOR DIRECT INPUT METHOD

PLS TELL FOR CALL TRANSACTION

[Former Member]

Hi Gopan,

if u want to use CALL TRANSACTION, method, u need to record the transaction using SHDB first, then generate a program for the recording n proceed as Vijay has suggested.

Hope it helps,

Regards,

Bikash