DTP Execution Error While deriving hierarchy Info Object

[Former Member]

Hi Experts,

I am working on finance G/L line item data where i have to Use G/L account Hierarchical data.so i am loading the G/L Account Hierarchies by creating transformations between 0GLACCEXT_T001_HIER->IOBJ 0GL_ACC .

Data is successfully loaded;But the error is coming at the time of execution of DTP.I checked my transformations RSDS also which is ok .so exact point of error ,i am unable to figure out.

So can you guys please provide me the solution for this issue.I have attached the screenshots of error in DTP.

Thanks

Ashish

[Former Member]

Hi Ashish,

Please check the Transformation Mapping for Hierarchy structure.

There are chances that the mapping are not proper and give this error.

Regards,

Bhavya K

[Former Member]

Hi Bhavya,Thanks for Response.

I have checked the transformations already. Still I am sharing the Screenshots of Hierarchy Data Transformations for G/L account.please check that and suggest me the solution.

Thanks

Ashish

[Former Member]

Hi Ashish,

I have seen the screen shots.

Just to check once, can you remove the mapping for 0OBJECTID in all and make it initial and try to load.

Thanks,

Bhavya

[Former Member]

Hi,

Once Psa requst delete and same also delete requst in DTP then load once agin..check it

Thanks

Dinesh

[Former Member]

Have you tried debugging the DTP?

[Former Member]

ya, i tried.but found that some problem in transformation with GLACCEXT IOBJ ,but not sure exactly.

[RamanKorrapati]

Hi,

Are you able to see dtp montior screen, menu Request-->push manually option in enable mode?

if yes then select failed data packet and select push manually.

Thanks

[Former Member]

Hi Rama,Thanks for response;

But i am n't able to get that option- "menu request in monitor screen" Can you send some screenshot of this steps.

Thanks

Ashish

[RamanKorrapati]

Can you share your whole dtp  monitor screen.

I want to see all menu and tool bar options.

[Former Member]

Hi Raman,

Thanks for response . Ya absolutely i can share my detail DTP monitor screen with you.

Just check the screenshots below.and i have already attached the ERROR Screenshot.

Thanks

Ashish

[RamanKorrapati]

Hi Ashis,

I asked DTP monitor screen along with menu and tool bar screen shot dear.

You shared information is DTP details not monitor screen.

No problem.

Am sharing my dtp monitor screen and check push manual(red mark) option(between refresh and debuggiong options) was availbale on our screen.

After the error if you didn't take any actions then you may see above options.

Thanks

[Former Member]

Hi raman,

I didn't get that option of PUSH MANUAL between Refresh and Debug Button.I am using BW 7.3.

i am attaching the screenshots.please check that.

Thanks

Ashish

[RamanKorrapati]

Hi,

reactivate your transformations and delete failed request.

I again trigger and load the data.

processing terminated is general error message.

Can you click on yellow icon against your error and share that info here.

Thanks

[Former Member]

Hi Raman,

Please check - this is the Detail Description of my error Message While executing the DTP.

Thanks..

[RamanKorrapati]

Hi,

Have you used error handling/dtp concept?

if yes please check those settings. But form your previous reply error handling was deactivated.

Cross check your dtp error handling settings and remove them if its deactivated.

Even please share Long text of your error.

click on below red mark area which shows exact error details.

Thanks

[Former Member]

Yes Raman , I am checking that ERROR HANDLING Setting - you can check in screenshot that It has two options:

A. DEACTIVATED

B.NO UPDATE,NO REPORTING.

I just want to know which option should i select or how to remove this DEACTIVATED Option.?

Thanks.

[RamanKorrapati]

Hi,

Go to  DTP in change mode and use Error handling - no update and no reporting.

Later save and activate your dtp.

if its not allowed then create new dtp and set above settings.

Later run your dtp.

Thanks

[Former Member]

Ya i followed your suggestion and make Error Handling Setting - No Update,No reporting and activate DTP and Execute it Newly.But here also i faced errors for Error handling Settings.check it.I.E in both options for Error Handling Settings i got the same error-"Update Terminated in accordance With Error handling setting".so where is the Exact prob is. Is it a prob in default Transformation ?or something else??

Thanks