report

[Former Member]

hi in reports if i select one radio button the second should be in disable mode ..how to do this ? what is the code for this?

[Former Member]

Hi Balu,

If you are talking simply about radiobuttons, then if you create two or three radiobuttons in your report and desire that they should behave in a mutually exclusive way, then you can assign them all to one group, which will make only one radiobutton to be selected at a time.

eg.

parameters: r1 radiobutton group g1 default 'X',

r2 radiobutton group g1,

r3 radiobutton group g1.

However if you want a block (of fields) to be disabled when another radiobutton has been enabled, you can go in this way :

At selection-screen output.

if r1 = 'X'. "checking which radiobutton is selected

loop at screen.

if screen-name = 'AGE'. "checking the name of the field which has

"to be disabled

screen-input = '0'. "disabling the field

modify screen.

endif.

endloop.

else.

loop at screen.

if screen-name = 'NAME'.

screen-input = '0'.

modify screen.

endif.

endloop.

endif.

Hope, this helps you.

[Former Member]

Hi Balu,

If u want to disable a block plz go through this code u can understand.

AT SELECTION-SCREEN OUTPUT.

LOOP AT SCREEN.

IF SCREEN-GROUP1 = 'RAF'.

IF VAL = 1.

• SCREEN-INPUT = 0.

SCREEN-INVISIBLE = 1.

MODIFY SCREEN.

ELSE.

VAL = 2.

*SCREEN-INPUT = 1.

SCREEN-INVISIBLE = 0.

MODIFY SCREEN.

ENDIF.

ENDIF.

ENDLOOP.

AT SELECTION-SCREEN ON CUST.

SELECT SINGLE * FROM KNA1 WHERE KUNNR = CUST.

IF SY-SUBRC <> 0.

MESSAGE E000(0) WITH 'ENTER CURRECT INPUT'.

EXIT.

ELSE.

VAL = 2.

ENDIF.

START-OF-SELECTION.

SELECT VBELN ERDAT NETWR FROM VBAK INTO TABLE ITAB WHERE KUNNR =

CUST OR VKORG = SALES OR VTWEG = DCH .

LOOP AT ITAB.

WRITE : / ITAB-VBELN, ITAB-ERDAT, ITAB-NETWR.

ENDLOOP.

Rewards some points.

Rgds,

P.Nag

[Former Member]

Hi,

For a radio button, second button is always disabled when u select the first one. But make sure that both the radio buttons are under same group.

eg: PARAMETERS: rb_typ RADIOBUTTON GROUP g1 DEFAULT 'X'.

PARAMETERS: rb_grp RADIOBUTTON GROUP g1.

regards,

Sekhar.

[former_member873340]

Kindly let us know how many radio buttons are there?

[Former Member]

hi Balu,

try this code

parameters: p_check4 as checkbox user-command ucom,

p_check5 as checkbox user-command ucom,

p_check1 as checkbox default 'X' modif id ABC,

p_check2 as checkbox modif id BCD,

p_check3 as checkbox modif id CDE,

p_check6 as checkbox user-command ucom.

parameters: p_matnr like mara-matnr modif id ABC.

parameters: p_werks like marc-werks modif id BCD.

at selection-screen output.

if not p_check1 is initial.

loop at screen.

if screen-group1 <> 'ABC' and screen-group1 <> ' '.

screen-input = '0'.

modify screen.

endif.

endloop.

endif.

at selection-screen.

if p_check1 is initial.

loop at screen.

if screen-group1 <> 'ABC'.

screen-input = '1'.

modify screen.

endif.

endloop.

endif.

if this helps u reward points

ravi

[Former Member]

Hi Balu,

If you are talking simply about radiobuttons, then if you create two or three radiobuttons in your report and desire that they should behave in a mutually exclusive way, then you can assign them all to one group, which will make only one radiobutton to be selected at a time.

eg.

parameters: r1 radiobutton group g1 default 'X',

r2 radiobutton group g1,

r3 radiobutton group g1.

However if you want a block (of fields) to be disabled when another radiobutton has been enabled, you can go in this way :

At selection-screen output.

if r1 = 'X'. "checking which radiobutton is selected

loop at screen.

if screen-name = 'AGE'. "checking the name of the field which has

"to be disabled

screen-input = '0'. "disabling the field

modify screen.

endif.

endloop.

else.

loop at screen.

if screen-name = 'NAME'.

screen-input = '0'.

modify screen.

endif.

endloop.

endif.

Hope, this helps you.

[Former Member]

hi Balu..

Paste this code..

parameters:

p_r1 radiobutton group g1 modif id SCR <b>user-command</b> RAM,

p_r2 radiobutton group g1 modif id SCB default 'X'.

<b>at selection-screen output.</b>

<b> if p_r1 = 'X'.

loop at screen.

if screen-group1 = 'SCB'.

screen-INPUT = '0'.

modify screen.

endif.

endloop.

ENDIF.</b>