Internal Tables

[Former Member]

I have an internal table with 3 fields namely matnr,date & GR qty. Now from this internal table...i have to calculate the GR qty for each material based on dates and range of dates?

[Former Member]

Hi Chandra,

You can do this using the internal table control/events like AT NEW and SUM. Its not that difficult to build a logic.

Regards,

VJ

[Former Member]

Hi,

If you have a ALV report then all the totals / subtotals by specific fields can be done by the user using the toolbar options.

Else, you will have to use the AT NEW / ON CHANGE commands with in the Internal table LOOP and calculcate the totals manually.

Regards,

Ravi

Note : Please mark all the helpful answers

[Former Member]

Hi

This you can do using control brake statments .

that is at new-endat, at first, at last etc

for every change in material you can sum up the quantites according to date

Thanks

[Former Member]

Hi Chandra,

Try with this logic.

SORT itab BY date matnr.

LOOP AT itab INTO wa_itab.

SUM = SUM + wa_itab-gr_qty.

AT END OF date.

wa_itab_1-date = wa_itab-date.

wa_itab_1-matnr = wa_itab-matnr.

wa_itab_1-gr_qty = SUM.

APPEND wa_itab_1 TO new_itab.

CLEAR wa_itab_1.

CLEAR SUM.

ENDAT.

ENDLOOP.

Regards,

Prakashsingh

Message was edited by: Prakashsingh Mehra

Message was edited by: Prakashsingh Mehra

[andreas_mann3]

Hi,

or use an extra int. table(sumtab) to calculate sums:

loop at itab.
 move-corresponding itab to sumtab.
 collect sumtab. 
endloop.

Andreas

[Former Member]

Hi!

Put control break AT END OF date inside the loop and inside it calculate the total by using SUM.

If ALV, just assign 'X' to subtotal/Total for the specified field.

Regards,

Sangeeta.

[Former Member]

Hi Chandra,

You can build a logic inside the loop of your internal table.

Sort the internal table

Loop the table

Keep on summing the qty ( untill your date condition is satisfied ).

Once u reach the last material either move the data to another internal table or write ( as per your req ).

For the same logic u can use AT END ,, ENDAT control processing inside the loop.

Get a look of a small piece of code doing somewhat similar workout.

DATA : BEGIN OF matqty OCCURS 0,

matnr(5) TYPE c ,

date LIKE sy-datum,

qty TYPE i,

END OF matqty.

DATA : sum TYPE i.

matqty-matnr = '10001'.

matqty-date = '20060413'.

matqty-qty = 10.

APPEND matqty.

matqty-matnr = '10001'.

matqty-date = '20060412'.

matqty-qty = 20.

APPEND matqty.

matqty-matnr = '10001'.

matqty-date = '20060419'.

matqty-qty = 30.

APPEND matqty.

matqty-matnr = '10002'.

matqty-date = '20060413'.

matqty-qty = 10.

APPEND matqty.

matqty-matnr = '10002'.

matqty-date = '20060419'.

matqty-qty = 10.

APPEND matqty.

SORT matqty BY matnr.

LOOP AT matqty.

" Date Condition.

IF matqty-date < sy-datum.

sum = sum + matqty-qty.

ENDIF.

AT END OF matnr.

WRITE: / matqty-matnr , sum.

ULINE.

CLEAR SUM.

ENDAT.

ENDLOOP.

Give it a try and if helps please reward point and close thread.

Any doubt , Please reply.

Regards,

Mayank