how can we create table in main window in scripts

[Former Member]

hi

experts

can u help me pzzzzzzzzzzzzz

[Former Member]

by using the BOX statement.

[Former Member]

Use the BOX, POSITION, and SIZE commands for drawing boxes, lines, and shading to print particular windows within a form or passages of text within a window in a frame or with shading.

Syntax:

/: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]

/: POSITION [XORIGIN] [YORIGIN] [WINDOW] [PAGE]

/: SIZE [WIDTH] [HEIGHT] [WINDOW] [PAGE]

BOX Command

Syntax

/: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]

Effect: draws a box of the specified size at the specified position.

Parameters: For each of XPOS, YPOS, WIDTH, HEIGHT, and FRAME, you must specify both a measurement and a unit of measurement. Specify the INTENSITY parameter as a percentage between 0 and 100.

Check this link

http://help.sap.com/saphelp_46c/helpdata/en/d2/cb3d07455611d189710000e8322d00/frameset.htm

Thanks,

Mahesh

[Former Member]

Hi,

See following link :

http://expertanswercenter.techtarget.com/eac/knowledgebaseCategory/0,295197,sid63_tax296859_idx0_off...

http://www.sap-img.com/sapscripts/faq-for-sap-scripts.htm

Reward points if helpful.

Regards.

Srikanta Gope

[Former Member]

Syntax:

/: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]

/: POSITION [XORIGIN] [YORIGIN] [WINDOW] [PAGE]

/: SIZE [WIDTH] [HEIGHT] [WINDOW] [PAGE]

BOX Command

Syntax

/: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]

Effect: draws a box of the specified size at the specified position.

Parameters: For each of XPOS, YPOS, WIDTH, HEIGHT, and FRAME, you must specify both a measurement and a unit of measurement. Specify the INTENSITY parameter as a percentage between 0 and 100.

XPOS, YPOS

Upper left corner of the box, relative to the values of the POSITION command.

Default: Values specified in the POSITION command.

The following calculation is performed internally to determine the absolute output position of a box on the page:

X(abs) = XORIGIN + XPOS

Y(abs) = YORIGIN + YPOS

WIDTH

Width of the box. Default: WIDTH value of the SIZE command.

HEIGHT

Height of the box. Default: HEIGHT value of the SIZE command.

FRAME

Thickness of frame.

Default: 0 (no frame).

INTENSITY

Grayscale of box contents as %.

Default: 100 (full black)

<b>Example</b>

/: BOX FRAME 10 TW

Draws a frame around the current window with a frame thickness of 10 TW (= 0.5 PT).

/: BOX INTENSITY 10

Fills the window background with shading having a gray scale of 10 %.

/: BOX HEIGHT 0 TW FRAME 10 TW

Draws a horizontal line across the complete top edge of the window.

/: BOX WIDTH 0 TW FRAME 10 TW

Draws a vertical line along the complete height of the left hand edge of the window.

/: BOX WIDTH '17.5' CM HEIGHT 1 CM FRAME 10 TW INTENSITY 15

/: BOX WIDTH '17.5' CM HEIGHT '13.5' CM FRAME 10 TW

/: BOX XPOS '10.0' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW

/: BOX XPOS '13.5' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW

Draws two rectangles and two lines to construct a table of three columns with a highlighted heading section.

Regards,

Pavan

[Former Member]

Hi,

You can use the POSITION and SIZE commands to set default parmeters for a box.

Instead of:

/: BOX XPOS '11.21' MM YPOS '5.31' MM HEIGHT '10' MM WIDTH '20' MM INTENSITY 10 FRAME 0 TW

You can write:

/: POSITION XORIGIN '11.21' YORIGIN '5.31' MM

/: SIZE HEIGHT '2' MM WIDTH '76' MM

/: BOX FRAME 10 TW INTENSITY 10

This can be usefull if you gave several boxes that share the same parameters.

If you want to set the position realtively to the window use POSITION WINDOW

to set the position to the top/left start of the window. Then use POSITION

to set the current position relatively to the start of the Window.

Note that you uses "+" or "-" in the ORIGIN position to the set the position relatively.

/: POSITION WINDOW

/: POSITION XORIGIN '5' MM YORIGIN '10' MM

the position is now 5 MM from the left and 10 MM from the top of the window

NOTE: After using the position command you can move the current position

realtively to the last used position

/: POSITION XORIGIN '10' MM YORIGIN '20' MM

Now the position will be X = 15 and Y = 30

Drawing a line. You can draw a line by setting the Height or Weidth to 0

and add a frane. E.g. a horizontal line:

/: SIZE HEIGHT '0' MM WIDTH '200' MM

/: BOX FRAME 10 TW XPOS '11.21' MM YPOS '14.81' MM INTENSITY 100

Regards

Sudheer