user defined selection screen sequence

[Former Member]

Hello Everyone,

I have a kind of an issue with selection screens. Story goes like this. I have a main sel.screen (no 1000) where I have some selection list. Now based on this selection i display another sel.screen (with my given number, let's say 9000). Then i fill selection criterion on screen 9000 press F8 and I get results. So far so good. Now when i 'back' button system displays the first, initial sel.screen (1000) instead of the last displayed (9000). I've tried to modify this behaviour and I am able to display the last sel.screen (9000) after pressing 'back' button but then when i press 'F8' instead of results I get initial sel.screen (1000) again. Is there anything I could do to make it work in the way I want to ?

Regards

Pawel

[Former Member]

Hi,

Could you paste the code where you are checking the sy-ucomm (Ok_Code) in the screen 9000?

Normally, we will set the screen as 0 to go back as below:

Leave to screen 0.

I just want to look into your code so that I can tell you an exact solution.

Regards,

Selva K.

[Former Member]

Hi,

Use set screen 0 instead of leave to screen 1000 or call screen 1000.

Because all called statments will make a stake and on back it will go back from where it was called.

Regards

Bikas

[Former Member]

Ok so let me present the code (or at least the most important parts) as Selva asked because using 'set screen 0' did not help. it is possible that I used it in wrong place so even more presenting code should help:

* some global data definition

*definition of mail sel.screen:
SELECTION-SCREEN BEGIN OF BLOCK selscr1
                 WITH FRAME TITLE text-001.
PARAMETERS: "select interface
     p_i001(4) as listbox visible length 20 OBLIGATORY DEFAULT 'XXX'.

SELECTION-SCREEN END   OF BLOCK selscr1.

*definiotion of following sel.screens;
SELECTION-SCREEN BEGIN OF SCREEN 1002.
  SELECTION-SCREEN BEGIN OF BLOCK selscr2 WITH FRAME TITLE text-001.
    PARAMETER: p_ws02(4) as listbox visible length 20 OBLIGATORY DEFAULT 'XXX'.
*    PARAMETER: p_t02 like GV_TABNAME DEFAULT 'zint_v_infin002'.
  SELECTION-SCREEN END   OF BLOCK selscr2.
SELECTION-SCREEN end OF SCREEN 1002.

SELECTION-SCREEN BEGIN OF SCREEN 1004.
  SELECTION-SCREEN BEGIN OF BLOCK selscr3 WITH FRAME TITLE text-001.
    PARAMETER: p_ws04(4) as listbox visible length 20 OBLIGATORY DEFAULT 'XXX'.
  SELECTION-SCREEN END   OF BLOCK selscr3.
SELECTION-SCREEN end OF SCREEN 1004.
*******************   END OF SCREENS ***********************************************************

AT SELECTION-SCREEN ON p_i001. "parameter from screen 1000
  CASE p_i001.
    WHEN '002'.
      call SELECTION-SCREEN 1002.
    WHEN '004'.
      call SELECTION-SCREEN 1004.

    WHEN OTHERS.
      CALL SELECTION-SCREEN 1000.
   ENDCASE.

*** some settings made basing on selections from following screens
AT selection-SCREEN on p_ws02.
  gv_werks = p_ws02.

AT selection-SCREEN on p_ws04.
  gv_werks = p_ws04.


INITIALIZATION
* filling listbox


 START-OF-SELECTION.
  CASE p_i001.
    WHEN '002'.
     "select 002 relevant data 
     "alv display
    WHEN '004'.
     "select 004 relevant data 
     "alv display
  ENDCASE.

  END-OF-SELECTION.

so as i mentioned before when i press 'back' on alv list I end up with screen 1000 instead 1004 (it's 1004 in real life not 9000). when i tried to change i was able to display 1004 selection when i pressed 'back' on alv but then instead of getting new list system takes ma back to 1000 scr again

regards

Pawel

[Former Member]

ok, i've solved it