IDOC

[Former Member]

Hi Guru,

I am doing one IDOC for Material Master. I have created the partner profile in WE20 and MATMAS message for that.

But when i am going for GENERATE PARTNER PROFILE then it is showing that "No messages have been defined for the selection conditions in the model ". So please let me know.

Then I am going for distribute the model. Then it is showing the message"RFC destination for synchronous communication (message type SYNCH) ". So what to do. Please help me.

Thanks,

Sandeep Garg

[Former Member]

have u created model view using customer distrubution model

tcode is bd64 create model view

[Former Member]

Hi,

I am not getting you exactly. But I have created the Model just clicking on "CREATE MODEL VIEW" and "ADD MESSAGE TYPE" button in BD64.

Please let me know??

Thanks,

Sandeep Garg

[soumya_jose3]

Hi,

While adding the message type you have given 'MATMAS' as message type in BD64 ?...

While generating partner profile you have to give the model you have created in BD64.

Regards,

Soumya.

[Former Member]

Hi Soumya,

I would appreciate your suggestion.

But I don't know where and how I have to add the Model.

Pls let me know.

Thanks.

[soumya_jose3]

Hi,

Firstly In BD64 click on the 'Create Model View' Tab.In the Pop Up that comes give a short text and Technical Name for the model and Enter. After creating this click on the model you have just created and then click on the tab 'Add message type'. There you have to give the message type as MATMAS and give ur sending and receiving systems. Then go to BD82(Generating partner profile) give the model view as the name of the model u have just created (technical name u created in BD64) and exceute. Now ur partner profile will get generated.

Regards,

Soumya.

[Former Member]

Hi,

I have attached the Model to partner profile also but it is showing the same error.

Thanks.

[soumya_jose3]

Hi Sandeep,

Have you saved your model view after creating in BD64?

Try saving after all your steps in bd64.

If not saved, this problem will arise.

Regards,

Soumya.

Edited by: Soumya Jose on Apr 10, 2008 11:34 AM

[Former Member]

Hi Soumya,

I have saved all the steps. Then I tried to add SYNCH message to OUTBOUND. And I add SYNCHRON as Basic Type. Then I observed in Model view In distribution the following error:-

Communication error occurred

Name or password is incorrect (repeat logon)

Please help me.

Thanks.

[soumya_jose3]

Hi Sandeep,

While Generating partner profile what message are you getting?

[Former Member]

Hi Soumya,

Here I am not able to attach the screen shot. Would you like to give me the Email id so that I can attach the screen shot.

Thanks,

Sandeep Garg

[soumya_jose3]

Just copy paste the message like say partner profile does not exist.

[Former Member]

When I am going to save the message in OUTBOUND in partner profile then it is not showing any error.But when I am going in BD64 in distribution model then it is showing the error as discussed.

I can send you the screen shot.

Thanks.

[soumya_jose3]

Hi,

It is not allowing to post email id.

What is ur RFC destination name? It should be same (case sensitive)as ur receiving system you have specified in BD64 while creating the model. If your RFC destination name is 'ABC' then the receiving system in bd64 should also be 'ABC' and not even 'abc' as it is case sensitive.

After correcting this try distributing again.

Regards,

Soumya.

Edited by: Soumya Jose on Apr 10, 2008 12:08 PM

[soumya_jose3]

What happened to ur issue?

[Former Member]

Hello Sandeep,

Try to add message type SYNCH to the outbound parameters of the partner profile and then regenerate the partner profile.

That may get you one step further.

Regards

Greg Kern

[Former Member]

Hi Greg,

When I am going to attach "SYNCH" message type to outbound profile. Then it is showing error message

"ENTRY SYNCH MATMAS01 does not exists in EDIMSG-Check your entry".

So pls let me know what to do????

Thanks,

Sandeep Garg

[Former Member]

Hi,

In we20(partner profile) insert 'synch' in both inbound and outbound parameter..I hope then it works fine....go this website

saptechnical.com....It is more useful...

Thank u,

Manjula Devi.D.