on 04-23-2010 10:59 AM
Dear Friends,
I have created one MIC. I have marked this as mandatory characteristic in control indicator tab.
In the inspectin plan for the material I have used the same charateristic.
I have used the control key. In the control key characteristic required is selected.
I have created one manual inspection lot. After that I have taken the UD without recording the results & put the stock to UR stock.
But the system is not giving any error message.
Regards
Use User Exit: QEVA0010 UD: Usage decision check
Logic will be if the status of all char is not "5" that means if RR not done for all char UD will not be allowed.
You can give Pop-up if all char are not chaecked.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Dear Anuradha,
You have to handle this by creating user profile which drives this activity, then assign this status profile to particular inspection type in QM SPRO, this will allow specific type Inspection to behave in the was you needed.
Following are steps :
1) Using T code BS02 create user profile, block UD if RR not done.
2) Create 2 user statuses INIT & QFIN in that status profile.
3) For INIT status use Business transaction 'Make user decesion' & assign radio buttons (Forbidd. & No action) also use business transaction 'Record Inspection Results' & assign radio button (Allowed)
4) For QFIN status use following Business transaction:
*Close - Insp Comple & Use radio button (allowed and set)
Complete Insp - short term & use radio button ( allowed & set)
start inv. postingbef. userdec & use radio button ( forbidon & no action)
5) Assign this status profile to inspection type in QM -SPRO
6) The material which you want to assign this activity, pl assign that inspection type to material.
7) Create inspection plan for that materials, pl see that at least one MIC has control parameter as 'Required characteristics'
Please let me know if this issue is resolved.
Best Regards,
Shekhar
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Irrespective of required, optional control indicators, the check is whether the MIC is valuated "5" or not. If it is having valuation status "1", "2" etc like anything other than "5", system will not allow UD unless we change the system status.
Means User status puerly depends upon MIC valuation status"5" completed.
Thanks
Vineeth
Hi Anuradha,
This you can restrict by defining the separate status profile and assigning that status profile to Inspection type in configuration.
By this this say if you assign that profile to 01 insp. type then all lots generated against GR against purchase order will have that profile. Unless you do RR system will not allow you to do UD.
Best Regards,
Shekhar
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi, You probably "forced" UD. Hence, the system accepted your UD. Pl. make changes to your role/userID as mentioned above. Regards, Krishna.Madduri
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
For that, you had to add the authorization object "Q_INSP_FIN" with values of "QPRUEFART" ,i.e. inspection type and WERKS, i.e. plant in your role/userid .
After that, system will give the necessary message.
Thanks
SUMIT
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
105 | |
12 | |
10 | |
5 | |
4 | |
3 | |
3 | |
3 | |
3 | |
2 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.