we19

[Former Member]

Hi all

I followed these steps for idoc>xi>http scenario as i saw in the forums.

SM59 rfc dest to int server (Type 3) // Sending System

WE21 tRFC port // Sending System

BD54 receiver sys as logical system // Sending System

SM59 RFC Dest to Sending sys from IS.(Type 3) //Int. Server

IDX1 Port Maintenance //Int. Server

IDX2 Load Metadata of IDoc //Int. Server

WE20 partner profile (o/b parameters) // Sending System

WE19 IDoc o/b processing for testing purposes // Sending System

I am getting problem in we19.........

I created an basictype idoc in we30.

I am trying to send that idoc from we19, but I am gettng an error 'port doesnot exist in the table of port description' when i click 'standard outboundprocessing' button

i performed all those steps lot of time but still getting the same.

Please help me.

Regards

Sim

[STALANKI · Accepted solution]

Can you give the reciever and sender ports and partner profiles from we19..edit control record.?

[Former Member]

Hi sudhir

These are the two numbered status shown on each idoc i can see inwe05

Status 37 EDI: Sender port in control record is invalid

Status 42 IDOC was ceated by test transaction

This Idoc has been generated through a test transaction.

Thankyu

[Former Member]

Hi

>><i>Status 42 IDOC was ceated by test transaction

This Idoc has been generated through a test transaction</i>

No prob with this as it come when we use we19

>><i>Status 37 EDI: Sender port in control record is invalid</i>

Enter the correct sender port.

Regards

Arpit Seth

[Former Member]

Hi Simon,

The Sender Port is invalid. If you can't find a valid Sender Port, then create one.

Do these two steps in the Sending R/3 system:

1. SM59 - Create RFC destination (Type=3) pointing to the sender system itself. Verify 'Test RFC connection' and 'Test authorization (F7)'.

2. WE21 - Create a tRFC Port, and select the above RFC destination.

Use this Port in the Control record of IDOC while testing from WE19.

Hope this helps!

--- Pops V

[Former Member]

Hi Simon,

In WE02 or WE05: Check if there are any existing MATMAS IDOCs that are sent out earlier.

Search with: No Date range, Direction=2, BasicType=MATMAS. This should find any existing IDOCs.

If any, Note one of the IDOC numbers.

Goto WE19, give the IDOC number and Create(F8).

Since the data for testing is already present, we only need to modify the Control record.

Click on Conrol segment (EDIDC) and modify the Ports; and then Start outbound processing (F7).

This should send the IDOC to the port given. This way the IDOC has a valid data, instead of filling something of your own.

Hope it helps!

-- Pops V

[Former Member]

Hi all

Thankyou for the quick responce.

All of your answers were really helpfull.

How can i find default MATAMS idocs that are ment for testing in we19.

Thankyou

[Former Member]

Hi Simon,

Go to transaction <b>WE19</b> and select your Idoc under the Basic type.

I hope it helps,

Thanks & Regards,

Varun Joshi

[Former Member]

Hi

>><i>error 'port doesnot exist in the table of port description' when i click 'standard outboundprocessing' button</i>

This is becoz ur testing outbound processing without giving values in <b>Control Record of Idoc</b>.

So do the following......

Go in we19 and give ur Idoc name.

Inside that u willl something like this

Control Record Name

|

|__Data Record Name

Click on ur Control Record Name and fill all the entries og Reciptent and Sender.

Then Click on Data Record Name and fill the data tht is to b sent by the IDOC and press enter.

Ur IDOC will successfully post.

Regards

Arpit Seth

[Former Member]

Hi Smith,

In WE19, Are you using an existing IDOC to resend or are you sending a new IDOC?

In case of new IDOC, fill in the data in the required segments; and most importantly fill in the data for control record (EDIDC).

Give the Recepient port - the one that is created in step 2 (we21).

Moreover, you missed a step in your list.

Making an entry in SLD for the Sender R/3 system. Create a TS and BS for the required client.

--- Pops V