cancel
Showing results for 
Search instead for 
Did you mean: 

Error while starting BI setup job : CCMS_BI_SETUP

nelson_chamba2
Participant
0 Kudos
522

Dear all,

Can someone tell me wish authorization should I give to the user solman_admin in order to enable him to update the service content on the Setup BW of my solution manager basic configurations step 5 (configure Automatically)

The error says that the job is being cancelled because of the this authorization.

Here is the error message:

#####

Job started                                                                    

Step 001 started (program RAGS_DSWP_SERV_CONTENT_UPDATE, variant , user ID SOLMAN_ADMIN)

No session packages to be updated

You do not have the authorization to update the service content

Job cancelled after system exception ERROR_MESSAGE

######

SM:SERVICE CONTENT UPDATE / 22202200

Best regards,

Nelson Chamba\

Accepted Solutions (1)

Accepted Solutions (1)

former_member183107
Contributor
0 Kudos

Hi Nelson,

Check transaction RSA1. If it asks "replicate metadata?" select "only activate". Then retry the step in SOLMAN_SETUP.

Regards,

Himanshu

former_member183107
Contributor
0 Kudos

Have a look at the role SAP_SMWORK_ADMINISTRATOR_COMP, this is the admin role for SAP Solman

Regards,

Himanshu

nelson_chamba2
Participant
0 Kudos

Hi Sharma,

Added the role but still.

Best regards,

Nelson Chamba\

nelson_chamba2
Participant
0 Kudos

YEEEEEESSSSSSSSSS - Done,

What I did was:

1. Assigned all roles mentioned on the other folks post

2. Run the transactions RSA1 and followed the tips

Many thanks,

Nelson Chamba\

former_member183107
Contributor
0 Kudos

Great to know that the issue is solved!!

Cheers

Himanshu

nelson_chamba2
Participant
0 Kudos

Yes, u can´t imagine how important it is to me.

all because of you all guys,

thank you

regards,

nelson\

Former Member
0 Kudos

Hi All,

One more tips, i had a same problem after system migration. I did all your suggestions (Role assignment etc..)but no luck.

Even if you don't get popup once enter the RSA1 T-code don't go back, in same page Goto -> Source system -> Right click Source system name in right side -> and click Activate. You will get error message if your source system not connected properly, then follow the error message.

My case Source system RFC is not working due to wrong Host and User name entry. Finally i changed right one and all went well.

Regards,

Vino

Answers (3)

Answers (3)

0 Kudos

Hi All,

CCMS_BI_SETUP job getting canceled.. please help.

Job Log:

Job started

Step 001 started (program CCMSBI_SETUP_CONTROLLER, variant , user ID SM_BW_ACT)

Job CCMS_BI_SETUP_20151209102817 successfully scheduled.

ERROR: Current Status: ERROR

ERROR: No parameters found (invalid setup ID 20150617161954)

Error occurred, check the logs

Job cancelled after system exception ERROR_MESSAGE

Regards

Ramesh

Former Member
0 Kudos

Hi Nelson,

1570399 - Solution Manager BI reporting Check if solman_admin has roles mentioned at note.

BR,

K.

Former Member
0 Kudos

I think this depends on the Support Pack you are using. Please use Solman_Setup to activate the customizing content, followed by an update of authorizations of your SOLMAN_ADMIN user after applying new support packs.

FYI , the following roles are required for BI content activation on SP10

SAP_BI_E2E

SAP_SM_BI_ADMIN

SAP_SM_BI_EXTRACTOR

nelson_chamba2
Participant
0 Kudos

Hi Patel,

Thank you for the feedback right, these roles were not there just the starting with Z. So I put them but the error still, but I can find on the logs the corresponding one on the list of canceled jobs.

Here you can find more information regarding ti.

1. The error still: Error while starting BI setup job : CCMS_BI_SETUP and the:

Message: A failure occured while calling CCMSBI_RUN_SETUP_IN_BTC at ABAP Host=localhost sys=00 client=001 admUser=SOLMAN_ADMIN rfcUser=SMD_RFC

Details: A failure occured while calling CCMSBI_RUN_SETUP_IN_BTC at ABAP Host=localhost sys=00 client=001 admUser=SOLMAN_ADMIN rfcUser=SMD_RFC !! Exception : BI_NOT_READY(Abap cause=/SLMCLNT001/LS//RSSEND////)

2. Please check the screenshot attached for more information.

Best regards,

Nelson Chamba\

karthikeyan_natarajan4
Active Contributor
0 Kudos

Hi Nelson,

Please double check the phase 2.4 create users in basic configuration so that all the user and required authorization is execute completely.

Also, in system preparation phase 1. create user for user solman_admin did you created and assigned all the proposed roles,

nelson_chamba2
Participant
0 Kudos

Hi N,

All these phase were passed correctly, do I need to re-run them after setting these authorizations roles?

Best regards,

Nelson Chamba\