cancel
Showing results for 
Search instead for 
Did you mean: 

Variant configuration t.code CU50 all BOM characteristics will display not a variant BOM

Former Member
0 Kudos

Dear Friends,

In Invariant configuration  t.code CU50 while click on result  button all the BOM is display . It has to display only variant BOM which i selected one. Kindly do the needful.pl find the screen shot.

Regards,

Sabhapathy R

Accepted Solutions (1)

Accepted Solutions (1)

former_member184627
Active Contributor
0 Kudos

Dear Sabhapathy,

The icon which you have clicked is for master data which shows all the BOM components.

Click the result icon, which is left to the master data icon.

Also, you can click the planned order icon, before costing icon.

Regards,

Senthilkumar SD

Caetano
Advisor
Advisor
Former Member
0 Kudos

Dear Senthil kumar,

In CU50 result screen shot

kindly  send me the screen shot which are all the necessary fields need to be maintained in CU01.

Regards,

Sabhapathy R

Former Member
0 Kudos

Dear Sabhapathy,

Have you maintained OD for all materials? If not then maintain OD for all because system will include all components during simulation which are without OD.

WR,

Ajay

former_member184627
Active Contributor
0 Kudos

Dear Sabhapathy,


Is the dependency COLOR_RED assigned to all components ?

It should be assigned only to RED color.

Create similar dependency COLOR_BLUE & assign to the bom component for blue color.

Regards,

Senthilkumar SD

Former Member
0 Kudos

Dear Senthil,

I have maintained all dependence for all BOM components.

Is this the below Source code  is same for all BOM components?, kindly confirm.

0000010 $ROOT.COLOUR= '01'

Regards,

Sabhapathy R

former_member184627
Active Contributor
0 Kudos

Dear Sabhapathy,

If your characterisitic COLOR has below values,

01 - RED

02 - BLUE

03- BLACK.

1. Your first dependency : COLOUR_RED says if COLOR ='01'. Assign this only to the component 60000055, which brings RED Color & not to other components.

2. Create another dependency in CU01: COLOR_BLUE.

     Sel. condition as COLOR='02'. Assign this only to the component 60000056 which brings blue      color.

Similarly create separate dependencies & assign to the respective components.

Based on your value selection in CU50, the right component will be displayed in the Results.

Regards,

Senthilkumar SD

kiran_kumar179
Active Contributor
0 Kudos

Sabhapathy,

Define Source codes as per your BOM sequence like

Red=0000010 $ROOT.COLOUR= '01'

Blue=0000010 $ROOT.COLOUR= '02' etc

Then assign same for BOM items respectively then test in CU50.

BR
KK

Former Member
0 Kudos

Dear Senthilkumar,

Thanks for your replay..,I try that also .it won't works..

0000010 $ROOT.COLOUR= '01'

0000010 $ROOT.COLOUR= '02'

0000010 $ROOT.COLOUR= '03' up to 13 i have maintained .



kindly send the steps by steps for CU01 and CU50 With screen shot.


Regards,

Sabhapathy R

kiran_kumar179
Active Contributor
0 Kudos

Sabhapathy,

It looks you took in a wrong direction.

For 3 different colors 3 different dependencies and for 3 engines 3 different dependencies you need to create.

For Red,Blue and Black colors define dependencies like below and remember to assign same dependency in BOM item details.

Red to Red item details and Blue to Blue item details same way for Black.

0000010 $ROOT.COLOUR= '01'

0000010 $ROOT.COLOUR= '02'

0000010 $ROOT.COLOUR= '03'


For engines also 1200CC,1500CC and 1800CC 3 different dependencies.


0000010 $ROOT.COLOUR= '01'

0000010 $ROOT.COLOUR= '02'

0000010 $ROOT.COLOUR= '03'


assign above engine dependencies to same item only.


Further if you have any items follow same procedure.


BR

KK

Former Member
0 Kudos

Dear Kiran,

Thanks Lot..Now it working fine..

Regards,

Sabhapathy R

Answers (2)

Answers (2)

Ritz
Active Contributor
0 Kudos

sabhapathy r,

If I have been at your place then i would have done it like below.

  • Former Member  made life easy of the many beginners by writing an document and i would have refer that to setup a basic VC model in system using link

  • If i am not clear and stuck up at very basic like , how to write and how many dependencies , i would have created 1 KMAT,  a Super BOM with just 3 materials as component , used basic selection condition selection  with syntax like ( characteristic 1 = ' 1')  which will select component 1 from BOM.

  • If it would not be working , i would have created my post on SCN explaining my VC structure , screen shot showing what i did , and my expectations from the VC i setup. I certainly wouldn't expect people will create an VC model and send me screen shot of each and every step when i cant do the same for my own knowledge building.

  • I hope  or say i am sure with this approach i would have save lot of my as well as fellow community members time and would have been move ahead to setup my next VC version 0.2 to add more features like other dependencies , change quantity , etc.

  • And last but not the list i would have marked replies helpful if it have help me. 

May be you can also try to follow this approach , hope it may help you.

Thanks

Ritesh

kiran_kumar179
Active Contributor
0 Kudos

Sabhapathy,

Did you defined object dependency in CU01 and assigned same to your BOM components?

BR
KK

Former Member
0 Kudos

Dear kiran,

Thanks for reply.i have maintained same in BOM components also.pl find the screen shot.

Regards,

Sabhapathy R

kiran_kumar179
Active Contributor
0 Kudos

Sabhapathy,

What is the Dependency type is used? Did you check for syntax errors exists?

Can you show us the BOM component Dependency Assignments to Objects snap shot?

And one more thing when you click on results in CU50 the screen heading should be Configuration:Results your screen shows Configuration:Master data?

BR
KK

Former Member
0 Kudos

Dear Kiran,

Please find the BOM component Dependency Assignments to Objects

Regards,

Sabhapathy R