Showing results for 
Search instead for 
Did you mean: 

Rounding Issue with Pricing Conditions

Former Member
0 Kudos

Currently we have in place a pricing hierchery that consists of two pricing conditions. ZP for base price and ZD for a +-differential. Both conditions begin with 00. ZP00. ZP01, ZP03, ZP04. If a ZP01 exists it overrides a ZP00. If a ZP03 exists it overrides ZP00,ZP01, etc. So basically the higher the number means it overrides anything underneath it. The ZD conditions are setup exactly the same way. I am currently running into a round issue. We settle all transactions in USD however the manual and differentials are often based on prices that go out more than 2 decimal places. SAP is treating the calculation for the ZP and ZD as two separate calculations. It rounds each of them and then combines for a total price. So if the base price ZP02 is $2.245 multiplied by quantity 3,999 = $8,977.755 which it rounds to $8,977.76 and the differential ZD02 is $.0235 this = $93.9765 which it rounds to $93.98 for a total price of $9,071.74. However if you add the ZD02 + the ZD02 you get a total unit price of $2.2685. This multiplied times the quantity 3,999 = $9,071.731 which is correct. But because SAP does each calc separately the price comes out to $9,071.74 or off 1CT. I have seen various solutions on how to fix this from user exits to creating additional conditions that takes both ZP and ZD conditions and calculates them as one but I was hoping someone had come up with something better? Or if there was a preferred method?

Accepted Solutions (0)

Answers (2)

Answers (2)

Active Contributor
0 Kudos


Go to V/06...Select both Group Condition and Item condition...

Then try again...

I think Martina has explained in more details......



Former Member
0 Kudos

Good Evening,

1. Please review NOTE 80183 regarding Rounding.

Values calculated in pricing are always rounded to the amount of

decimal places which the used document currency owns. As subsequent

processing steps setup on this rounded value rounding differences can

occur in the calculation of the price per unit or in subtotal line.

To bypass such effects note 80183 describes possible solutions to

reduce / bypass this effect.

A few problems in rounding after applying note 80183, variant 2 have

been recorded where it was recommended to use the formulas 919 and

920 on all discounts and surcharges that appear before NETP and the

problem was solved.

2. In transaction V/06 there is a field under header 'Control data1'

which can effect how the system rounds off condition values during


->> Rounding rule

The rule that determines how the system rounds off condition

values during pricing. The last digit will be rounded.


o In the standard rounding rule '_', values are rounded off according

to business standards:

10.454 -> 10.45 DEM

10.455 -> 10.46 DEM

o In rounding rule 'A', values are always rounded up:

10.459 -> 10.46 DEM

10.451 -> 10.46 DEM

o In rounding rule 'B', values are always rounded down:

1045.9 -> 1045 LIT

1045.1 -> 1045 LIT

In this example, the currency of the condition rate is Italian Lira.

The Italian Lira does not have any places after the point.

3. Also check if the condition type is set as item condition as well

as group condition in transaction V/06. What this means is that

the system will calculate the value of the condition on header level

and compares it with the sum of item values in the document.

Any rounding difference (KONV-KDIFF) detected, will be populated

in the line item with greatest value or in first line item if all are

of equal value.

In other cases where there is no adjustment because there is no

rounding difference when comparing the header value and the sum of

item values.

->> Solution to this scenario -

If you remove the 'group condition' setting, the system will then

calculate amount for the items directly and you will not get the

rounding. You must decide which setting is more suited for your

business. This is not a bug, but works as per designed.

EXAMPLE: MWST - tax condition (a group condition)

Item 10 16% of 100.90 = 16.14

Item 20 16% of 100.90 = 16.14

Total = 32.28

I hope this helps you!

Kind Regards,

Martina McElwain

SD Forum Moderator