cancel
Showing results for 
Search instead for 
Did you mean: 

MCIJ

Former Member
0 Kudos

Sir,

In MCIZ , i am only getting Fuel Volume and Total costs.

I am not getting Distance i.e Km readings.

please advice me.

VSrao

Accepted Solutions (1)

Accepted Solutions (1)

Former Member
0 Kudos

Hi VSRAO

Make sure that you have entered the measuring position(DISTANCE or which ever configured) in all measuring documents and execute the report.

Regards

Seenu

Former Member
0 Kudos

hi

1. Define cosumable type: Diesel ( created in MM01)
2. Make settings for unit type
   M2-volume consumption/Distance
   Define valid consumption unit:006, l/100km

3. Define counter
   Distance_km-consumption relevant to distance counter
   Fuel: Consuption relevant to fuel counter
   Time: Consumption relevant to time counter

4.Define calculation method: 

Calculation Method-A
Disp unit: 006
Unit Text:l/100Km
fuel counter-Fuel
primary counter:Distance_km
Days short-10
Days long-30

and all other settings like standing order assign to ie01, fuel and oters in ie01, calculation in ie01 etc assigne.

5. goods movement & account assignment

code-03

goods isse-261

reversal-262

standing order check-yes

Still I am not getting distane i.e km in reports.

please help me.

former_member187991
Active Contributor
0 Kudos

hi

whether the measurement position created for fleet objects is specified in the measuring point for the equipment and also check whether the same is updated in the config

Regards

thyagarajan

Former Member
0 Kudos

hi

yes

what ever i created in fleet objects, the same was take as measuring position and updated in equipment.

Settings

hi

1. Define cosumable type: Diesel ( created in MM01)
2. Make settings for unit type
   M2-volume consumption/Distance
   Define valid consumption unit:006, l/100km

3. Define counter
   Distance_km-consumption relevant to distance counter
   Fuel: Consuption relevant to fuel counter
   Time: Consumption relevant to time counter

4.Define calculation method: 

Calculation Method-A
Disp unit: 006
Unit Text:l/100Km
fuel counter-Fuel
primary counter:Distance_km
Days short-10
Days long-30

and all other settings like standing order assign to ie01, fuel and oters in ie01, calculation in ie01 etc assigne.

5. goods movement & account assignment

code-03

goods isse-261

reversal-262

standing order check-yes

6.  spro -->PM --->Information systems --->configure
measurement document update - settings updated   as mentioned by Deepak sir.

Still I am not getting distane i.e km in reports.

Former Member
0 Kudos

hi,

the same measurement positions which created in fleet objects were assigned as measuring points.

others like charasterstics also takne as same.

Still I am not getting distane i.e km in reports.

Data

Define cosumable type: Diesel ( created in MM01)

2. Make settings for unit type

   M2-volume consumption/Distance

   Define valid consumption unit:006, l/100km

3. Define counter
   Distance_km-consumption relevant to distance counter
   Fuel: Consuption relevant to fuel counter
   Time: Consumption relevant to time counter

4.Define calculation method: 

Calculation Method-A
Disp unit: 006
Unit Text:l/100Km
fuel counter-Fuel
primary counter:Distance_km
Days short-10
Days long-30

and all other settings like standing order assign to ie01, fuel and oters in ie01, calculation in ie01 etc assigne.

5. goods movement & account assignment

code-03

goods isse-261

reversal-262

standing order check-yes

please help me.

HiteshMistry
Participant
0 Kudos

Hi VSRAO,

In your 6th step check reference indicator for Key figure 'IAMENDISTT'. It should be 'A'.

Hitesh

Former Member
0 Kudos

Dear Hitesh,

done the settings,('IAMENDISTT'-A).

still, I am not getting distane i.e km in reports.

former_member187991
Active Contributor
0 Kudos

hi

please refer the following sites

http://www.scribd.com/doc/39621775/EAM-ConfiguringFleetMgt

Regards

Thyagarajan

HiteshMistry
Participant
0 Kudos

OK, Have you did further settings as well ? check the following,

Select that line & double click on 'Assign to Measuring Point (Ref. Indicator 'A')' & maintain following values,

Unit system : MET

Key Figure name : IAMENDISTT

Measuring position : (This should be special measuring position defined by you like DISTANCE)

Int. meas. unit : KM

Hitesh

Answers (4)

Answers (4)

Former Member
0 Kudos

Dear Deepak, Hitesh, Thyagarajan.K, Pankaj Kumar & Seenuvasan

Many thanks for your prompt response and also pateince with respect to the queries raised by me.

The main issues are come due ignore these settings given in the below path.

spro -->PM --->Information systems --->configure--->measurement document update.

Many thanks to Hitesh & Deepak & others for sharing thie knowldge.

Note: Thread closed.

Former Member
0 Kudos

Hi Vsrao van,

for fuel do the setting

Former Member
0 Kudos

Dear Hitesh,

Done the settings as told by you.

Gone to the dcomentation send by  Thyagarajan.

Shown to basis people.

They siad every thing is ok. tole some settings or alignment is missing form fucntional side.

I dont know exactly where the problem lies.

Please provide some hints on this.

One agian thanks for your time and also yours patience.

Vsrao

Former Member
0 Kudos

Dear all,

As told by hitesh,

Select that line & double click on 'Assign to Measuring Point (Ref. Indicator 'A')' & maintain following values,

Unit system : MET

Key Figure name : IAMENDISTT

Measuring position : (This should be special measuring position defined by you like DISTANCE)

Int. meas. unit : KM

I think the real problem lies in thsese settings only. And basis people also unable to understand thsese key settings.

Now

I am getting Km readings. Many Thanks to all of you.

But I am not getting Fuel readings

Kind attn: Hitesh & Deepak & Thyagarajan,

Please guide me some settings like similar to get fuel also.

VSrao

Former Member
0 Kudos

Hi,

Please respond some one.

Vsrao

Former Member
0 Kudos

HI VSRAO,

Please update on the input parameters you are providing in MCIZ.

Regards,

Deepak

Former Member
0 Kudos

hi,

1.equipment no:ok

2. equipment category-ok

3. Planning plant:ok

4. Technical obj. type: ok

5. analysis period: 01-12 to 05-12

Former Member
0 Kudos

Hi VSRAO,

There is a Function Module written for that updation.Please check if you have mapped correct function mosule.

Please refer screenshot for detailed config.

Regards,

Deepak

Former Member
0 Kudos

hi deepak,

what is the tcode to go to this fucntin module.

Former Member
0 Kudos

Hi VSRAO,

Please follow the path SPRO -> PMCS -> Information system for PMCS -> Configure Measurement Document Update

Regards,

Deepak