cancel
Showing results for 
Search instead for 
Did you mean: 

BOM setup problem

Former Member
0 Kudos

Hello Guru,

for material 10076168, BOM alternative 5 is setup from 2008.11.13 in production version, but if you check it in the production orders, system still uses alternative 1. Where and what could be the problem?

Thanks

Ryan

Accepted Solutions (1)

Accepted Solutions (1)

rupesh_brahmankar3
Active Contributor
0 Kudos

Dear,

If Lot size validity date are same then system always use first alternative. Check the seting of OPL8 for manual selection of production version. And MRP 4 View of material master for BOM selection method-2 selection by production version.

Regards,

R.Brahmankar

Former Member
0 Kudos

Hello R Brahmankar

as i check MRP4, production version from lot size 0,000 and to lot size 0,000 same from the two production version.but selection method is blank.

thanks

rupesh_brahmankar3
Active Contributor
0 Kudos

dear,

Miantain the setting in MRP 4 View of material master for BOM selection method-3 selection by production version only. And you can also lock the production version that you don't want to use.

Please try and come back.

Regards,

R.Brahmankar

former_member184655
Active Contributor
0 Kudos

Dear Ryan,

What's your production order start date? Does it fall before 13.11.2008?

Please check this, or else give your requirement's date some more future date,now check whether the

system is picking the second prod.version or not?

Regards

Mangalraj.S

Former Member
0 Kudos

Dear Ryan,

Check the alternative BOM status in header data is 2 or 1, if it is 2 change it to 1

regards,

sree

Former Member
0 Kudos

Hello brahmankar,

i will try this one

Edited by: Ryan on Nov 19, 2008 11:28 AM

rupesh_brahmankar3
Active Contributor
0 Kudos

Dear,

Yes you need to active the production version tick mark in material master.

Do the consistency check in your production version where green light is appearing or not?

Is your second alternative BOM is valid for Production ?

Then run MRP with planning mode -3 deleted and created then convert planned order in to production order and check your result.

Please revert back for further discussion.

Regards,

R.Brahmankar

Answers (5)

Answers (5)

Former Member
0 Kudos

check below points

Two production version should be available

Lock un necessary one

Check for lot size validity date

OPL8 should have manual selection of production version

MRP 4-SELECTION by production version should be maintained

Check BOM status

Check whether prod version is having correct data with green light

Former Member
0 Kudos

Hi,

Check in the Master data Tab Page of the Production Order the Explosion date.

If the explosion date is before 13.11.2008 the BOM Alternative which is Valid on the explosion date

will be there in the Production Order.

Thanks,

nandha

Former Member
0 Kudos

If you have more production versions, goto matl master in mrp4 view keep the required production version on top of other versions and give selction key as 2.

or

else lock other versions which is not required. In production version main screen you will get lock and unlock option.

please check it

madlercm
Active Contributor
0 Kudos

Hi,

Check definitions to make sure that master data is selected by production version, and also that start date of production order (or original planned order) is not before validity date of new alternative.

If you still can, make a new reading of master data in the production order.

Also check a BOM explosion with today's vality to make sure that alternative 5 is chosen. If not, you may have a problem in the way you manage the validity.

Regards,

mario

former_member184655
Active Contributor
0 Kudos

Dear Ryan,

Were the BOM changes made once after the production order was created?

Please check once again the BOM alternative in the production version.

Check the Lot size in the production version and MRP4 view settings for BOM selection and your order

type dependent parameters in OPL8.

In CO02,top menu -


> functions---> Read PP Master Data,so that the system picks up the latest

BOM assigned and the order status will get changed to created,if it's already been released.

Regards

Mangalraj.S

Former Member
0 Kudos

Dear Ryan,

if u have created new alternative to the BOM also u need to create new Prod. version in C223. then while creating the order CO01/CR01, u need to select by clicking on Production version push button on top left of the corner.

If order is already created go to order change CO02/COR2, click on Master Data tab. here in the production version column click on icon(red, yellow and green) in front of the version then it we will display all available versions for the material u select whicj one u want. here version will appear if u create it in C223 only.

i hope this will help u, any thing else get back

Regards,

sree

Edited by: sree gowda on Nov 19, 2008 10:42 AM

Former Member
0 Kudos

Hello,

it is usually are production order was been created automatically that come form planned order, now in the master data MRP4 view of our material there were 2 version maintain, which is PG01 which valid from 02.09.2008 to 13.11.2008 which had alt bom=1, but now this version is not valid as of todays date, so we expect version PG02 which valid from 13.11.2008 to 31.12.9999 which had alt bom=5 will be the one should be pick up by the production order automatically. why until now version which is not valid anymore still been automatically been pick up?

thanks

rupesh_brahmankar3
Active Contributor
0 Kudos

Dear,

13:11:2008 is comman date so whay that its selecting first alternative.

You can do one thing go to MM02--MRP4 view in production version there is option lock for any usage and save the material master and then try.

Regards,

R.brahmankar

Former Member
0 Kudos

Dear Mr.,

ur ending date of frist version and starting date of second version is clashing. can u change the starting date of second version to 14.11.2008 and see

regards,

sree