Application Development Discussions
Join the discussions or start your own on all things application development, including tools and APIs, programming models, and keeping your skills sharp.
cancel
Showing results for 
Search instead for 
Did you mean: 

Error in BDC

anupam_srivastava2
Participant
0 Kudos
387

Hi All

In T-code ME22, i want to change netprice. i am uploading the data from a flat file.

not good with BDC, its given me errro msg

Call_transcation M22 Returncode = 1,001 Record 0

E formatting error in the field RMO6e-EBELP see next msg

E input should be in the form _________

***********

My code is

report ZME22_BDC

no standard page heading line-size 255.

include bdcrecx1.

parameters: dataset(132) lower case.

      • DO NOT CHANGE - the generated data section - DO NOT CHANGE ***

*

  • If it is nessesary to change the data section use the rules:

  • 1.) Each definition of a field exists of two lines

  • 2.) The first line shows exactly the comment

  • '* data element: ' followed with the data element

  • which describes the field.

  • If you don't have a data element use the

  • comment without a data element name

  • 3.) The second line shows the fieldname of the

  • structure, the fieldname must consist of

  • a fieldname and optional the character '_' and

  • three numbers and the field length in brackets

  • 4.) Each field must be type C.

*

      • Generated data section with specific formatting - DO NOT CHANGE ***

data: begin of record occurs 0,

  • data element: BSTNR

BSTNR_001(010),

  • data element: AUFEP

EBELP_002(005),

end of record.

      • End generated data section ***

start-of-selection.

*perform open_dataset using dataset.

*perform open_group.

CALL FUNCTION 'GUI_UPLOAD'

EXPORTING

FILENAME = 'C:\test.txt'

  • FILETYPE = 'ASC'

HAS_FIELD_SEPARATOR = ''

  • HEADER_LENGTH = 0

  • READ_BY_LINE = 'X'

  • DAT_MODE = ' '

  • CODEPAGE = ' '

  • IGNORE_CERR = ABAP_TRUE

  • REPLACEMENT = '#'

  • CHECK_BOM = ' '

  • NO_AUTH_CHECK = ' '

  • IMPORTING

  • FILELENGTH =

  • HEADER =

TABLES

DATA_TAB = record

EXCEPTIONS

FILE_OPEN_ERROR = 1

FILE_READ_ERROR = 2

NO_BATCH = 3

GUI_REFUSE_FILETRANSFER = 4

INVALID_TYPE = 5

NO_AUTHORITY = 6

UNKNOWN_ERROR = 7

BAD_DATA_FORMAT = 8

HEADER_NOT_ALLOWED = 9

SEPARATOR_NOT_ALLOWED = 10

HEADER_TOO_LONG = 11

UNKNOWN_DP_ERROR = 12

ACCESS_DENIED = 13

DP_OUT_OF_MEMORY = 14

DISK_FULL = 15

DP_TIMEOUT = 16

OTHERS = 17

.

IF SY-SUBRC <> 0.

MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO

WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.

ENDIF.

*do.

*read dataset dataset into record.

loop at record.

if sy-subrc <> 0. exit. endif.

perform bdc_dynpro using 'SAPMM06E' '0105'.

perform bdc_field using 'BDC_CURSOR'

'RM06E-BSTNR'.

perform bdc_field using 'BDC_OKCODE'

'=AB'.

perform bdc_field using 'RM06E-BSTNR'

record-BSTNR_001.

perform bdc_dynpro using 'SAPMM06E' '0120'.

perform bdc_field using 'BDC_CURSOR'

'RM06E-EBELP'.

perform bdc_field using 'BDC_OKCODE'

'=BACK'.

perform bdc_field using 'RM06E-EBELP'

record-EBELP_002.

perform bdc_transaction using 'ME22'.

*enddo.

endloop.

*perform close_group.

perform close_dataset using dataset.

1 ACCEPTED SOLUTION

amit_khare
Active Contributor
0 Kudos
171

Run the BDC in foreground and check the field record-EBELP_002 from your file.

The current format of the field is incompatible to to your settings with the corresponding field.

May be u have taken different data types for both or different format then EBELP in ME22.

Regards,

Amit

Reward all helpful replies.

4 REPLIES 4

Former Member
0 Kudos
171

Hello AJ,

Make this change in ur code:


data: lv_bstnr(010).
write: record-BSTNR_001 to lv_BSTNR. " Check here
perform bdc_field using 'RM06E-BSTNR'
LV_BSTNR." Check here

If useful reward.

Vasanth

Former Member
0 Kudos
171

This is because of the format error in the line item number. Check the value and format of EBELP in the internal table (all the line items) and fix it accordingly.

Naveen

amit_khare
Active Contributor
0 Kudos
172

Run the BDC in foreground and check the field record-EBELP_002 from your file.

The current format of the field is incompatible to to your settings with the corresponding field.

May be u have taken different data types for both or different format then EBELP in ME22.

Regards,

Amit

Reward all helpful replies.

0 Kudos
171

Hi Amit

Can any body provide with the source code for same.

thanks in advance

rgds

AJ