on 2022 May 19 10:47 AM
Good morning,
We have recently upgraded to the BW4HANA 2.0 version, and we have detected that some loads are slower, compared to the previous version of BW4HANA 1.0.
an example is the load of this DTP:
When dtp runs, it only shows one active job in the system.
and the system is not overloaded with processes, now that we are running it there are only two active jobs, so there is no reason for dtp not to multiplex the load.
Can you help me identify what could be the problem?
BR,
Request clarification before answering.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello pamarque
pamarque3 Processes are not really called "Performance" as it is the default setting. What Du you think?
Best Regards Roland
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi roland.kramer,
The problem is that even having the 3 processes, when the load is executed, in the trx sm50 only 1 process is released, and not the 3 processes parameterized. And the server is completely free of charge, with all batch processes free. So even if the number of batch processes increases, I think the same thing would happen. It is just the same problem that this note indicates, but it does not apply by version.
1158574 - 70SP18: DTPs no longer run in parallel after importing SP 16
BR,
Patricia.
Hi roland.kramer,
I have reviewed the document, and regarding the parameters of the RSBACTH transaction, I have seen that the DTP was not, therefore, not in the RSBATCHPARALLEL table either. I have activated the DTP, and I have rechecked the RSBATCHPARALLEL table, and the DTP already appears.
I've run the load next, and it's still having performance issues.
I have found this old post, and they talk about the problem I have.
https://answers.sap.com/questions/11553865/parallel-processing-in-dtp-level-not-working.html
This note is mentioned, but it is old, and does not apply to the version of BW4HANA 2.0
1158574 - 70SP18: DTPs no longer run in parallel after importing SP 16
Do you know if there is any similar sap note that applies to the new version of BW4HANA?
On the other hand I am also looking at this note,
2769125 - Composite Note: RSADMIN Parameter for SAP BW/4HANA
do you know if there is any parameter that we have to change related to this problem?
Thanks in advance for the help.
BR,
Patricia.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello pamarque
you should rather check with tx. RSODSO_SETTINGS as stated in the Document - Customizing SAP BW 7.x and BW/4
Best Regards Roland
please follow the Rules of Engagement
Hi Patricia
Have you try to apply SAP Note 2603241. I tell you my experience. We are in BW/4HANA 2.0 SP8. When I have an issue related to DTPs or transformations, the first thing we do is verify if SAP Note 2603241 has new updates. Many times applying this SAP Note solves the issue.
Be advised that, depending on the SP level you BW4 is on, it will apply several SAP notes so, be careful.
Regards
Hello pamarque
Did you checked the BW/4 Basis Customizing again?
Possibly some user values were reset during the SAP Upgrade ...
SAP BW Installation/Configuration on/for HANA => Customizing SAP BW 7.x and BW/4
Best Regards Roland
please follow the Rules of Engagement
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
74 | |
30 | |
9 | |
8 | |
8 | |
7 | |
7 | |
5 | |
4 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.