cancel
Showing results for 
Search instead for 
Did you mean: 

Error while loading 0f_aa_11

Former Member
0 Kudos
92

Hello frriends,

This is the error when Iam loading the 0FI_AA_11.

Error message from the source system

Diagnosis

An error occurred in the source system.

I have checked the source system also , please help me out.

This is urgent, points will be rewarded..

Thanks

Accepted Solutions (0)

Answers (16)

Answers (16)

udayabhanupattabhiram_cha
Active Contributor
0 Kudos

Hi:

Look at this thread, looks like your same problem.

SAp guys have a reply in this one.

Sry, wrong link first time -

<i>please check OSS note #755677. This is the only problem known to us in this area. If this does not succeed, please create a customer problem message.

Cheers

SAP NetWeaver BI Organisation</i>

Chamarthy

Message was edited by:

U.P. Chamarthy

Former Member
0 Kudos

also the problem in activating the transfer rules , giving syntax error . remember it is the standard buisness content ..

Former Member
0 Kudos

Error in source system ..

udayabhanupattabhiram_cha
Active Contributor
0 Kudos

Hi:

Looks like you have a problem with one of yoru Routines or the Start Routine.

If you wish, you can paste all your ROutines here and some of us will see if we can figure out the error.

Chamarthy

Former Member
0 Kudos

It is standard Buisness content only, no customized objects.

Former Member
0 Kudos

I think that may be a red herring - can you give us the job log from R3 for the failed asset afab load

Former Member
0 Kudos

When Iam activating tha transfer rules the error mess is

Syntax error in GP_ERR_RSAPTM2, row 24 (-> long text)

Message no. RG102

Diagnosis

The type "WITH" is unknown.

udayabhanupattabhiram_cha
Active Contributor
0 Kudos

Hi:

Did you check and see if some other errors exist.

Like, did you try Replication of Data Sources.

I am guessing RSA3 works.

So,

1) Try Replicating th edata sources again.

2) If you have any hard-coded selections in the infopackage, Remove them and load the data to PSA ONLY to make sure.

Look for dumps in R/3 - Transaction ST22

look in BW also -ST22

Chamarthy

Message was edited by:

U.P. Chamarthy

Former Member
0 Kudos

Whenever Iam loading Asset atrr and text , it is giving me the same error tah

ERROR in source system in detailed ERROR in data selection ..

Former Member
0 Kudos

Please tell us the exact message from the R3 job log - not the infopackage error

Former Member
0 Kudos

THanks for that much the sequence would be

1) 0ASSET - Text and Attributes at the same time

usign Flexible Update.

2) 0ASSET_AFAB_TEXT

3) 0ASSET_AFAB_ATTR

4) Attribute Chainge Run

5) 0FI_AA_11

But I have problem in activatin the transfer structure of 0asset text and aseet aftab.

udayabhanupattabhiram_cha
Active Contributor
0 Kudos

Hi:

Follow this esquence exactly as stated in the post:

Chamarthy

Former Member
0 Kudos

I dint get . But while loading asset_aftab_attr in delt amode itself Iam geting the same error ..

Former Member
0 Kudos

But when Iam loading that asset_aftab master , then also giving me the same rror that is ERROR IN SOURCE SYSTEM..

Former Member
0 Kudos

You have definately got all three running in delta mode?

Former Member
0 Kudos

But when Iam loading tha Asset master it is also giving me the same error

that ERRO IN THESOURCE SYSYTEM - ERROR IN DATASELECTION

Former Member
0 Kudos

Hi

check the dataselction given in the IP ..are u loading delta or init?

check at the RSA3 for the DS - for depreciation area ..

run the init with/0 any dataselections..... and then run the deltas...

after that run the 0FI_AA_11

hope it helps

regards

AK

Former Member
0 Kudos

start from scratch again

load asset - load asset afab - load aa11 and or aa12

the erros you are getting are because you haven;t init's or run the deltas properly in this order and this sequence

You cannot go any further - you must load the deltas in that sequence -

Former Member
0 Kudos

Ya but some got failed.

0ASSET_ATTR IS OK but 0ASSET_AFTAB_ATTR IS FAILED

Former Member
0 Kudos

hi

what was the error u got ...??

regards

AK

PS : unless u load perfectly the masterdata for Assest then u will get the error as the same when u load the )0FI_AA_11

Message was edited by:

A K

Former Member
0 Kudos

Error is ERROR OCCURS DURING THE DATA SELECTION.

Former Member
0 Kudos

It simply saying that Error in the source system. I don't know much about this..

If u can do anything please do it .

Thanks..

Former Member
0 Kudos

Is that what the job log in R3 says?

"Error in the source system"

??

Former Member
0 Kudos

ok - did you run in the asset master data first?

Former Member
0 Kudos

Hi

Can you specify the Error message you got in the source sys

Regards,

vishwa

Former Member
0 Kudos

Did you run asset_attr_text and asset_afab in first?

these are hardcoded in the extractor - they need to run before the AA datasources otherwise you will get an error (check the r3 job log and it will tel you)