cancel
Showing results for 
Search instead for 
Did you mean: 

datasource error loading data for 2lis_02_s015

Former Member
0 Kudos
265

Hi can anybody help me with this

i have installed business content 0PUR_C03. it is using datasource 2lis_02_s015. datasource is available in bw and it is active. when i go to infosource and create infopackage and schedule and mointor . it gives me error like this

<b>Error message from the source system

Diagnosis

An error occurred in the source system.

System response

Caller 09 contains an error message.

Further analysis:

The error occurred in Extractor .

Refer to the error message.

Procedure

How you remove the error depends on the error message.

Note

If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the moment, and restart the request .</b>

when i go click on the Error messages . it shows me this error

ID

<b>LIS updating is still activated(client300) M+ 25

Errors in source system RSM 340</b>

i dont know what it means . hope you can help me .

thanks alot in advance .

Accepted Solutions (0)

Answers (3)

Answers (3)

BerndSieger
Product and Topic Expert
Product and Topic Expert
0 Kudos

Regarding your initial error M+ 025:

Perhaps you misinterpreted the customizing transaction which you used to look up the updating status of the S015 (tr. OMO2). "Asynchronous updating" means that the updating is active.

You can do the following: Start tr. SE16, select with MCINF = 'S015'. This should show you one record. Does the field KBTCH of this record contain a number (= active updating) or a blank (= no updating)?

If there is a number, you indeed need to switch off the updating before your initial load can succeed. Start the tr. OMO2, put the cursor on the line for the S015 and click the Parameters button. Now on the popup select "No updating", confirm and do not forget to save on the entry screen.

Hope that helps,

Bernd Sieger

Former Member
0 Kudos

Hi Sri,

I think you need to generate the delta update by using RMCSBIWC in your R/3 (if you have already done an init ?)

To be able to generate the delta update for an information structure, you must deactivate the update of this information structure temporarily in all clients.

Deactivate the update using the LIS Customizing or report RMCSBIW0 (see Note 146294) in ALL clients of the OLTP System in which the information structure is updated.You can activate the update again after generation.

Hope it helps!

Bye,

Roberto

Former Member
0 Kudos

hi roberto

i have tried has it was mentioned in oss notes . transaction RMCSBIWC AND RMCSBIW0 does not exist in r/3 but lbw1 exists and using this i checked for all the clients and each client i found it is inactive and asynchronous update . when i do the full update i dont have any problem .when i want to intilize the delta the process i t give same error says Lis is active . so how can i activate the delta process . thanks .

Former Member
0 Kudos

What I suggested were reports (SE38) and not transactions!

Anyway, take alook to LBW0 to see if you need an acivation of your delta updating...

Bye,

Roberto

Former Member
0 Kudos

Hi Roberto,

In the same scenario, is there any way to do fresh delta Initialization somehow?

Regards,

Ashish

Former Member
0 Kudos

Hi Veda,

As discussed,Datasource 2lis_02_s015 is the part of Application MM and its available in R3.

Please check whether its in active state or not.

Have you checked in transaction RSA3? its working or not.

Wait for other expert suggestions.

Regards,

Ashish Goel