Add attribute 'Planning Group' to other planning levels

[reddyatoz]

I would like the Planning Group from Planning Group Level to be added as an attribute field on the 'Location | Product' and the 'Resource' planning levels.

Please find attached pictures of how it should look.

All values used on 'Location | Product' and 'Resource' Should be created in 'Planning Group' beforehand, if not i would like IBP to return attached Rejection Code.

While testing with one Planning Group, the objective is to have planning group as a single filter value to get a combined Planning View with Product Location and Resources.

When input data in Planning Group i would expect the yellow marked line to be a fault. since that name isn't a IBP stored Planning Group.

I have the same issue on 'Resource level'

Br

Kumar

[raghunathpartha · Accepted solution]

Hello Kumar

Please add attribute check similar to PLUNITID in screenshot below

Steps to Follow:

1. Open Location Product Master Data

2. At the Bottom enable Attribute check "ON"

3. Select Planning Group Master Data and select check attribute as "Planning Group"

4. Select assigned Attribute as "Planning Group"

5. Activate MDT and Dependent PA

6. Observe that Planning Group check is enabled and those records which are not in "Planning Group" are not accepted for that attribute

7. Repeat steps 1 to 6 for Resource MDT also

[reddyatoz · Accepted solution]

Hi Raghunath,

Yes, it worked. Thanks for the quick response.

Small query : Planning group accepting data when i upload data in capacity group only. Planning group rejecting data when there is no data in capacity group.

Where can i find the relation between capacity group and planning group.

Thanks once again.

Br

Kiran

[raghunathpartha · Accepted solution]

Hello Kumar

Can you please share the screenshot of the rejection reason you are facing?

Thanks and Regards

Raghunath

[reddyatoz · Accepted solution]

Hi Raghunath

When i upload data without capacity group

t is rejected with below error

When I upload data in capacity group first then planning group accepting it. I have maintained planning group TEST in MD.

Br

Kiran

[raghunathpartha · Accepted solution]

Hello Kiran

This issue looks little strange because from what I see there is no linkage as you are using Planning Group from separate MDT. Can you please do more testing and see if this is due to some ambiguity in planning levels because of both attributes?

Thanks and Regards

Raghunath

[reddyatoz · Accepted solution]

Hi Raghunath

planning group attribute is key attribute in PLANNINGGROUP MDT.

But I added this to LOCATONPRODUCT MDT as normal attribute.

Do you think will that be an issue here.

Br

Kumar

[raghunathpartha · Accepted solution]

Hello Kumar

I have seen multiple examples where such attributes are added in MDTs.

Example 1:

Example 2: Planning Unit

This is Key from Planning Unit (simple mdt) and also assigned in Location Product MDT as non key

Example 3:

The one I setup, to test your case . I didnt come across this issue and system is accepting combinations technically.

So, the issue could be little difficult to identify, as this kind of same attribute usage across multiple MDTs is not so common for supply planning master data.

Please also find some caution before applying this change to any PA which already has data below

https://help.sap.com/docs/SAP_INTEGRATED_BUSINESS_PLANNING/da797ae2bf6246d58abd417f24915d55/8fa4bb8f...

[reddyatoz · Accepted solution]

Hello Raghunath

When I was checking location product MDT I could see that there is a attribute check for capacity group.

When I remove this attribute check from LOCPRD MDT system accepting combinations.

Is that something I am missing?

Br

Kumar

[raghunathpartha · Accepted solution]

Hello Kumar

You mean there was such check previously added in Location Prodict MDT?

Are you not able to add Planning group check without Capacity group check?

This additional check seems to be the reason..But the question is you added it or it got auto added?

[reddyatoz · Accepted solution]

Hi Ragunath

Thanks for the support.

is it possible to check below question

Key figure calculation to use current technical week | SAP Community

Br

Kumar

[reddyatoz · Accepted solution]

Hi Raghunath,

As you can see here the loc/Resource is set with a planning group

And then i use that planning group in the filter for creating a view.

however when i see the view i can't understand the logic behind what IBP shows.

to my understanding i would only expect to have the yellow line appear, but i don't get why the planning group isn't shown on the combination. as we see in the first picture it should be New_Test.

Br

Kiran

[raghunathpartha]

Hello Kumar

For Key-Figures at resource level, as per your design, you need to assign "Planning Group" as non root attribute in planning level from Resource MDT for it to show in WKRESLOC Planning levels

Thanks and Regards

Raghunath

[reddyatoz]

Hi Ragunath

I am able to see 'Planning Group' attribute at WKRESLOC level.

But when i try to filter data with 'Planning Group'.

data should reflect for existing combinations only.

Location ID Resource ID Planning Group

3330 3330_Line1

3330 3330_Line2 New_Test

In planning view, it is showing all data.

Br

Kiran