Material Replication Problem: Products are not displayed in COMMPR01

[Former Member]

Hello,

I am working with SRM 7.0, Backend: SAP ERP 6.0 EHP4

My problem is that when I have replicated the Material from R/3 with the tcode R3AS all messages are green and Ok( tcodes R3AM1,SMQ1,SMQ2,ST22,SMWT) But I see Non products in SRM by tcode COMMPR01.

In SRM the Range are SRM external match with R/3 internal.

I have replicated from R/3 to SRM the following Category:

MAT_ and it subcategories.

I have already replicated OK the following:

DNL_CUST_PROD0

DNL_CUST_PROD1

DNL_CUST_SRVMAS

Could anybody, it would be weell appreciated.

Kind regards,

[ricardo_cavedini · Accepted solution]

Hello,

Check if table COMM_PRODUCT has been populated in SRM.

Also, consider the following notes:

872533 FAQ: Middleware

720819 Middleware consumer entry for SRM in OLTP syst

Kind regards,

Ricardo

[Former Member · Accepted solution]

Hello,

I have followed the note 720819 about fullfilling the tables:CRMCONSUM,CRMSUBTAB,CRMPAROLTP,SMOFINICON,ETC.

Every seems ok.

Still in tcode R3AM1; the following are Green (Done, ok 😞

DNL_CUST_PROD0

DNL_CUST_PROD1

DNL_CUST_SRVMAS

the following are Green (Done, ok ):in column of blocked indicates Zero value.

MATERIAL

SERVICE_MASTER

About SMQ1,SMQ2 in both system no queues are shows.

In table SMOMARA and COMM_PRODUCT no values exist.

I have the following doubt related to Replication concerning Material and Service Ranges:

I have created the R/3 ranges and indicated these as Internal and for the same ranges in SRM indicated as External. I think this is ok, isn`t it?.

Welcome any suggestion..

Kind regards,

Edited by: ital230 on Jul 23, 2010 1:05 PM

[Former Member]

solved

[Former Member]

Hi Alberto Rauda,

   I am facing the same issue, Could please tell me the process how to resolve it.

Thanks

Gaurav Gautam

[bharathi_ponnusamy]

Hi ,

I am also facing the same concern where the R3AM1 status is perfectly green. There are no pending queues in SMQ1 and SMQ2. There are no Bdocs in the system and also no run time errors.

Could you please help me on this.

Best Regards,

Bharathi

[Former Member]

Hello Bharathi P

      Did you maintained any filter for the downloading the materials.

Thanks

Gaurav

[bharathi_ponnusamy]

Hi Gaurav,

Thanks for your update. We haven't maintained any filters.

Best Regards,

Bharathi

[Former Member]

Hello Bharathi P,

     I would request you to please create a new thread. And then provide me with your screenshots. Where exactly you are facing . Also let me know the steps for your loads.

Thanks

Gaurav Gautam

[bharathi_ponnusamy]

Sure Gautam. Will do that.. Thanks for your update.

Best Regards,

Bharathi

[Former Member]

Solved!

followed the note 720819

BDoc in txn:SMW01

AC01 object types attending to ID view.

Thanks Ricardo and Muthu

Edited by: ital230 on Jul 30, 2010 1:12 PM

[Former Member]

Dear Muthu,

1)Yes, I have already pulled the categories: have two hierarchies:

R3MATCLASS assigned to Purchasing

R3PRODSTY ;assigned to Product and has under the categories as MAT_; for example: MAT_HAWA

2)Yes all the categories are contained in table comm_category.

Fullfilled Backend tables:

CRMPAROLTP

CRMRFCPAR

CRMSUBTAB

Kind regards,

Edited by: ital230 on Jul 22, 2010 2:08 PM

[Former Member]

Hi

Did you pull the product category first?

can you see the material group in comm_category table first?

Hope that you have done all set ups in BACKEND TABLES ?

Muthu

[Former Member]

Hi,

one question: in the backend table CRMSUBTAB I have CRS_MATERIAL_EXTRACT but this does not exist in CRMSUBTAB for SRM.which is the correpondant so?.

Kind regards,

[Former Member]

so far you are correct. dont bother in srm table. not required.

Any clues in SMW01 OR slg1 .

you must get some clue.

What about your filters on material only purchasing view ?

Muthu