- SAP Community
- Groups
- Industry Groups
- SAP for Utilities
- Discussions
- Replacement Value Procedure - Activation
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011 May 20 1:33 PM
- SAP Managed Tags:
- Utilities
Hi all,
Is there any thing to be done to activate the replacement value procedure apart from the following standard configuration steps I have already done:
User Status
Status Priority
Replacement Value Creation
Profile Calculation under Formula Profiles
Interface to external Systems
When I upload the profile values through EEDM07, with some missing data, the missing values are not being replaced.
With thanks & regards,
Vinodh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011 May 20 2:10 PM
- SAP Managed Tags:
- Utilities
Did you define a replacement value procedure group in the header of the profile you are importing onto?
If so, did you define the procedure correct in customizing? Sap Utilities -> Energy Data Management -> Profile Management -> Replacement Value Creation -> Define Replacement Value Procedure (define the procedures, then define the Group based on the proecures)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011 May 20 2:10 PM
- SAP Managed Tags:
- Utilities
Did you define a replacement value procedure group in the header of the profile you are importing onto?
If so, did you define the procedure correct in customizing? Sap Utilities -> Energy Data Management -> Profile Management -> Replacement Value Creation -> Define Replacement Value Procedure (define the procedures, then define the Group based on the proecures)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011 May 23 8:03 AM
- SAP Managed Tags:
- Utilities
Hi,
Thanks for the reply. The steps you have mentioned have already been done. Still unresolved...
Regards,
Vinodh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011 May 23 8:48 AM
- SAP Managed Tags:
- Utilities
Did you set the checkbox 'RVP After Imp.' in the configuration of the RVP group?
This sets the RVP to be executed immediately after import. If you haven't set it you do the RVP from EDM1 or from EEDM02 to replace the missing values.
If you have set this and still not working, stick a breakpoint in the FM (for the replacement value procedure) you expect to be executed. Then upload some values through BAPI_ISUPROFILE_UPLOAD.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2011 May 27 10:48 AM
- SAP Managed Tags:
- Utilities
Hi,
Thanks for the prompt reply and excuse me for the delayed response. Have been trying various options. Still does not work.
I have set the checkbox 'RVP After Imp.' in the configuration of the RVP group. But still RVP is not working.
EDM1 - When I click "Generate Replacement values for Profile", I get message "Select a valid Line" & When I click "Generate all replacement values", I get message "0 profile(s) edited successfully; 0 profile(s) ended with error(s)"
EEDM02 (Display profile values) - I think you meant EEDM01 (Change Profile values). When I clicked " Carry out mass change" button I got message " No missing values" eventhough there was a missing value displayed as 0.
Also not knowing where to set the breakpoint in the FM.
Futher when I set the Consistency Check Group in the Profile Header, the import does not work using FM but works when I use the EEDM07 route.
With thanks & regards,
Vinodh
