SAP for Utilities Discussions
Connect with fellow SAP users to share best practices, troubleshoot challenges, and collaborate on building a sustainable energy future. Join the discussion.
cancel
Showing results for 
Search instead for 
Did you mean: 

Error during creating for RTP interface

former_member266656
Participant
0 Kudos
521

hi,

while creating rate for against RTP billing getting an error as per attached print shot. Although I have already created RTP component an RTP interface for the same. Pls suggest possible reasons for the error.

Regards

Girish

8 REPLIES 8

Former Member
0 Kudos
456

HI Girish,

Please go to result tab inside your RTP interface, check whether you have defined quantity as a output operand category of your RTP interface! I think instead of quantity you might have given something else!!!

pls revert back if u have any doubt

Rohit

Former Member
0 Kudos
456

Hi Girish,

Please assign Result number of RTP to your operand QTYRTPFBD in Rate Fatcs.

Hope it solves your problem.

Regards,

Rajesh

former_member266656
Participant
0 Kudos
456

Thanks Rajesh & Rohit for your valuable comments.

  

Rohit, I am getting errors while I am making changes to RTP interface, Formula & RTP components. while entering the data as per our requirement and trying to save it system doen not save any data. Print shots are attached. Pls suggest. All entries as can be seen in print shots gets omitted when saving the trasaction.

Rajesh how can I assign Result number of RTP to operand QTYRTPFBD in Rate Fatcs, pls suggest the t code.

Also pls suggest am I doing the right entries.

Regards

Girish

0 Kudos
456

Hi Girish,

Goto tcode EA31 and click on Facts.

Please go through the below link.

http://help.sap.com/saphelp_rc10/helpdata/en/5f/c4743c4dc1623de10000000a114084/content.htm

Hope its useful.

Regards,

Rajesh

0 Kudos
456

Hi Girish,

              I don’t see any error screen shots! Just only tabs in which a message, no change is shown !

Have you created those screen shots at the time of creation of RTP interface? Because I didn’t see any RTP component activated in your interface screen shots which u have provided!

   It would be more helpful if u could provide me the scenario where u want to use this interface ! I could help u more !

  Also for giving the result parameter from RTP interface to your rate please go to T-code ea31 -> in rate facts ->give the result number to the corresponding RTP operands !please do note that result operands category and operand which u are using in the Rate should be of same operand category !

ROHIT

0 Kudos
456

Hi Rajesh

As per my first screen shot I am unable to save the rate for RTP, hence can not go in the change mode of rate for rate facts i.e EA31. First I need to create and save a rate for RTP and so far I am unable to do that. Pls guide

Regards

Girish

0 Kudos
456

Hi Rohit,

In the screen shot I have enetered the data for eg for RTP interface under the RTP component tab, the data you could see there like RTP Component I have enetered RTPCOFBD but while saving the transaction and again checking it in display mode, the data does not appear there ie. system says no changes have been made.

Sir,

We are in gas utility business and we provide gas to industrial. commercial & domestic customers.

Regards

Girish Bahuguna

0 Kudos
456

Hi Girish,

  • First of all fill ur header tab in RTP interface
  • Then as per your requirement give your result parameters in result tab.
  • In rtp component first of all give ur component name , priority ,activation type  then  click on the add symbol
  • The component will be replicated to the next half of screen ! give ur activation date and click on the copy option!
  • Then give ur input and output parameters node wise
  • This is an example of a RTP interface screen once the entry has been made !
  • Hope u have screen after completing ur interface according to ur requirement
  • If u have doubts in RTP interfaces please refer to IUT235 and any doubts please refer back any time
  • And pls don’t call me as sir

ROHIT