EDI: Partner profile outbound logical message not available

[former_member201804]

Hello Experts,

I have now export declaration, and it is complete in all sense. Upon the simulation I have received the message "EDI: Partner profile outbound logical message not available". Although I have outbound logical message for idocs is intact at WE20 I believe?

Please see the below screen shot

Processing log details:

and this processing details I have mapped with EDP13 to the partner profile from WE20. Now I am bit confused what else is missing. Can any one of you please help me to clear this?

Kind Regards,

Alex.

[former_member201804 · Accepted solution]

Hi All,

Just resolved the issue and for which I have taken the following steps.

1. Checked the master data for the customs management at default data for the document - Office of Departure if it was right? - Corrected.

2. Checked the Partner Profile in WE20 for the partners Customs Office and logical system.

3. GTS Menu - System communication and selected an isolated outbound message and corresponding inbound message and checked with the settings of partner profile with respect to the message as enclosed

and found that in the logical system config of partner profile was missing the outbound parameters as shown below:

I have made black rectangle arround CUS_OFF1. As I am just simulating first so SIMULATION is my office of departure for the testing and later I can change it with CUS_OFF1.

and with all these the result now looks as below:

Just the question to experts is : the red circle is showing processing. What does this means? is there any more steps to perform?

Thanks for reading.

Kind Regards,

Alex.

[former_member215181 · Accepted solution]

Hi Alex,

The "envelope" icon informs that the Declaration is locked whilst awaiting the inbound response from the Customs Authority. If the simulator is set up correctly, that inbound message should be generated and processed, re-setting the processing status.

Regards,

Dave

[former_member194424]

Hi Alex,

My sincere apologies, I meant business partner SLLCPS (vendor). Regards, Satish

[former_member201804]

Yes I have.

[former_member194424]

Hi Alex,

Can you check if the partner has been created in transaction BP (at least with role SLLCPC)?

[former_member194424]

Hi Alex,

Isn't that a separate issue in a separate thread? For the benefit of everyone, could you please respond there and close this thread if resolved.

Regards, Satish

[former_member201804]

Hi Satish,

As the issue is still existing where I am unable to process my CD I will wait for some more feedbacks. Thanks for you inputs

Kind Regards,

Alex.

[former_member194424]

Hello Alex,

Sorry, I'm confused a little. There is a screenshot of IDOC so is the IDOC generated or are you continuing to have issues? in WE20 (display mode), when you click on Position (Ctrl + Shift + F10), you will see this pop-up. Then enter the partner. If it exist, the cursor should move to the found one.

Please also ensure that the partner status is A (Active, partner profile can be used).

[former_member201804]

Hi Satish,

I have still the same issues where I am declaring customs declaration to CUS_OFF1 with simulation transaction code /n/sapsll/idoc_sim and upon which when I entered the document no: XXXXX I can see the outbound message in communication tab is going under process but not reciving any inbound message in the simulation.

1. No partner found for logical message /SAPSLL/CUS_EXP

2. EDI Partner profile outbound logical message not available

and in response to the no:1 error I asked your help if anything to do with partner profile setup. I hope I could clarify your confusion.

and now regarding your latest screen shot then please see the steps what I did.

1. I have put the cursor on CUS_OFF1

2. then select utlities -->Idoc output-->you will get automatically choose partner with partner no: and partner type as CUS_OFF1 and partner type as GP

3. then Run with a clock and you will see the following popup

and now in the above, When I clicked Partner No: nothing comes.

Thanks,

Alex.

[former_member194424]

Hello Alex,

Could you please re-process the message in customs dec and attach the results? Thanks

[former_member201804]

Hi Satish,

Please see post reporcessing status:

and when I check the message in next line No partner found for logical message...

what is this partner agreement please?

Thanks,

Alex.

[former_member201804]

Also I tried to analyze the partner profile for CUS_OFF1 I could see something which is bit puzzeling

In WE20 I selected CUS_OFF1 and selected Idoc output I got this popup where I want to enter the recepient partner idoc in Partner No: but nothing comes up and gets the message no values found. which means I dont have recepient partner?

Is it any significant to the above message no partner found for logical message /SAPSLL/CUS_EXP?

Looking for your help.

Kind Regards,

Alex.

[former_member194424]

Hello Alex,

Based on your screenprint, it appears there is no need for message code and message function. Please see my screenshot. Regards, Satish

[former_member201804]

Hi Satish,

I have also made an another entry without MC and MF and still the same.

Regards,

Alex.