cancel
Showing results for 
Search instead for 
Did you mean: 

issue related to ID Origin of Contacts

sinaei
Contributor
0 Kudos
556

Dear Experts,

I have a question regarding to Contact ID Origin:

We are creating an interaction Contact via FM : "CUAN_CE_INTERACTIONS_POS"

Like below:

ID_ORIGIN: "GIGYA",
ID: 123456789 ,
SMTP_ADDR: Chiara@Test10.com ,
EMAIL_OPTIN: X 

It will create this Contact for us also related Interaction:

ID_ORIGIN: "GIGYA"ID: 123456789

And it will create 3 Facet

Now imagine that we want to create another Interaction for this contact with Type of Email Address "Chiara@Test10.com" with mention FM

Since this Email Address is just assigned to one contact and there is facet for this contact with mention email, I expect to create me another Interaction with Email ID Origin for the same contact!
But It creates me another contact and this interaction will assigned to new contact

Could anyone help me to understand what can be the issue?

Thanks
Sepide

Accepted Solutions (0)

Answers (5)

Answers (5)

vineet_kaul
Contributor

Hi Sepide,

Can you check the FM call, how you are creating the Interactions. The FM has an option to set mode of operation. by default it is should be set to D which means it will perform merge and match of contact, can you try to set the default mode to N and then execute the same scenario and see if any difference.

Thanks

Vineet

sinaei
Contributor
0 Kudos

Hi Vineet and Akil,

Thanks for your both reply.

Actually the issue is that we do not want to merge these contact, I mean we modified the BADI to do Drop.
This BADI is a little bit complicated...we defined in the BADI to decide Drop mode, but the problem was that it always did Drop!

So at the end we ought to define when do the Drop decision.

Thanks a lot

vineet_kaul
Contributor
0 Kudos

Hi Sepide,

I am a little confused, your question states that the problem is that it is not merging the contacts but creating a new contact and assigning the interaction to it, and in the above reply you mentioned "we do not want to merge these contacts". The system is doing as you expect it to be? or am i missing the point.

Can you please confirm the following.

1.Email id has been set as shareable.

2. Create a contact first with Gigya Id along with email address, but please use SE-37 FM CUAN_Interaction_post to create this contact

3. now using the same se 37-FM please create another interaction but using same email id as the origin as above for ease of use please maintain both email address in uppercase and ensure they are not case sensitive as the screen shot in your initial problem show different email addresses. upper and lower case.

4. Check what contacts are created in ROOT and FCET table after you create above two interactions.

Thanks

Vineet

SauMaris
Contributor
0 Kudos

See customizing for origins of contact and have you allowed to have email sharable or is it non-sharable.

Maris

sinaei
Contributor
0 Kudos

Hi Maris,

I checked this settings, and they are correect.
The issue was related to the BADI that we implemented.

Thanks
Sepide

sinaei
Contributor
0 Kudos

Hi Koumar,

We have activated the BADI (Interaction Contact Update BADI)

and it seems that when ithe Badi is active the system is goint to another way!

I mean we copied from the standard one and there is nothing custom modifictaon in the BAdi, but as we found if the BAdi is Active is doing another way.

Do you have any idea?

Thanks
Sepide

Former Member

Dear Sepide,

If you use the BAdI as is, there shouldn't be any issues. Did you check the suggestion that Vineet had on what you used in the header section of your FM "CUAN_CE_INTERACTIONS_POST"?

With regards,

Akil

Former Member
0 Kudos

Dear Sepide,

In your customizing, what did you set for ID_ORIGIN email? Is this set to one per contact?

With regards,

Akil

sinaei
Contributor
0 Kudos

Hi Komur,

In our customizng ID_Origin of Email is Not sharable

I can nou undrestand why in FACET we have three ID_ORIGIN (That are correct) but in Interaction we have just one
and if I want to create a new interaction with the email that is exist for that customer, It will create me another customer.

Former Member
0 Kudos

If you have someone that can debug in your team, you can have a look at what the BAdI for the interaction (contact) upload does when trying to find an existing IC to match the interaction. It might be something really stupid, like the difference bwteen lower/upper-case.

In my experience your interaction should have been added to the existing IC.

With reggards,

Akil

sinaei
Contributor

Hi Komur,

Thanks for your help.
I will do debug the BADI and will let you know. Because we have activated the BADI for merging Contact and we decide to do "Drop".

Thanks again
Sepide

former_member226
Employee
Employee
0 Kudos