Question Re: Quality Management Datasources in Technology Q&A

Quality Management Datasources

Former Member — Wed, 26 Mar 2014 10:13:08 GMT

Hi,

I am able to see the inspection lot in the transaction QA33 and qals table but i am unable to find the data in the data
sources in 2LIS_05_QE1 and 2LIS_05_QE2. Users has posted the data but im unable to find the data in my datasource.

Please give some idea on this.

Thanks & Regards,
Kavitha

Re: Quality Management Datasources

sriramvijay_ravidoss — Wed, 26 Mar 2014 10:16:59 GMT

Hi Kavitha,

Have you followed all the LO cockpit steps and filled setup tables for these datasources.

If so pl mention steps u followed

-Sriram

Re: Quality Management Datasources

former_member182998 — Wed, 26 Mar 2014 10:20:19 GMT

Hello Kavitha,

I agree to Sriram ! Can you furnish little more details, like where you are not able to see the data ( which t Code you are using to check) , Have you checked RSA3 , etc.

Please suggest more on this line , so that we can drill down.

Regards

Re: Quality Management Datasources

RamanKorrapati — Wed, 26 Mar 2014 10:21:01 GMT

Hi,

above data sources LO data sources, you need to fill the setup tables, later you can see the data at RSA3 or info pack level(if triggers).

Deleteing and refilling setup tables for LO data sources(full load) is common.

Thanks

Re: Quality Management Datasources

former_member199945 — Wed, 26 Mar 2014 10:31:50 GMT

Need to FIll set up table then data will come. If set up tables also filed data is not coming means check the same in TCode : QA03 for 2LIS_05_QE1 & 2LIS_05_QE2 : tcodes :QE03.

Re: Quality Management Datasources

former_member186399 — Wed, 26 Mar 2014 10:34:28 GMT

Dear Kavitha

Please check whether result recording has taken place for the inspection lot. Only if the result recordings are done 2LIS_05_QE1 & QE2 will have the data.

You may find the data in 0INSP_LOT_ATTR for these inspection lot.

Regards

Gajesh

Re: Quality Management Datasources

Former Member — Wed, 26 Mar 2014 10:39:25 GMT

Hi,

Based on the update modes in LBWE for this data sources.delta records will come in to delta queus(RSA7)

So pls check whether V3 jobs is completed or not, if not completed,then run and check tha data.

Regards,

Malli

Re: Quality Management Datasources

Former Member — Wed, 26 Mar 2014 11:15:38 GMT

Hi,

Already I have followed all the steps mentioned above,However i am not able to find the inspection lot in the datasources 2LIS_05_QE1 & QE2.

I am able to find the data of Inspection lot in Tcodes : QA03 and QA33

Kindly guide me how to proceed further.

Regards,

Kavitha

Re: Quality Management Datasources

Former Member — Wed, 26 Mar 2014 11:24:24 GMT

Hi Kavitha,

Pls check the table QALS as filed name Lot -PRUEFLOS and materila as MATNR in ECC side.

And if youare using 0NOTIFICATN master data, 0INSP_LOT(Inspection lot number) is Dis.attribute of the 0NOTIFICATN

you can check in 0NOTIFICATN content also.

Regards,

Malli.

Re: Quality Management Datasources

former_member186399 — Wed, 26 Mar 2014 12:32:24 GMT

Dear kavitha

Please check whether result recording has taken place for the inspection lot. Go to QA33 > go to Result recording tab > and check whether the result recordings are done against the MIC.

If the data appears here then only QE1 and QE2 will have the data.

Regards

Gajesh

Re: Quality Management Datasources

Former Member — Thu, 27 Mar 2014 09:03:28 GMT

Hi,

Whenever we do changes in QA33, it is getting updated into LBWQ. After scheduling job i am unable to find the data in RSA7.

Please guide us.

Regards,

Kavitha

Re: Quality Management Datasources

RamanKorrapati — Thu, 27 Mar 2014 09:05:16 GMT

Hi,

How frequently you schedueld your V3 job.

Once you done chnages at QA33, later you can run V3 job.

after that you can see the records at RSA7.

Thanks

Re: Quality Management Datasources

Former Member — Thu, 27 Mar 2014 09:19:52 GMT

Hi,

We ran V3 job immediately in Dev system.

We are not getting any records in RSA7.whereas it is showing the no of records in LBWQ.

We are unable to find data even after doing setup tables process.

Please guide .

Regards,

Kavitha

Re: Quality Management Datasources

RamanKorrapati — Thu, 27 Mar 2014 09:23:06 GMT

For delta loads we get data from base tables not setup tables.

At RSA7, there is column total, it shows record count against all delta data sources.

First of all have you seen changed records at LBWQ?

are your sure, you selected queue delta method at LBWQ for your data sources?

Re: Quality Management Datasources

former_member182343 — Thu, 27 Mar 2014 09:26:22 GMT

HI,

Is that datasource is delta enabled .

In the mean time do set-up table run and check for that record at RSA3 with full load.

Regards, Vijay

Re: Quality Management Datasources

sriramvijay_ravidoss — Thu, 27 Mar 2014 09:27:19 GMT

May be you are filling wrong setup table and running wrong job for this particular Datsource.

are you able to get recorsds for init?

if yes, are you running job from LBWE JOB control?

Re: Quality Management Datasources

Former Member — Thu, 27 Mar 2014 10:18:36 GMT

Are you sure that you are running the correct V3 job...can you share the log of the completed V3 job here. Are any records fetched in there from MCEX queue.

Best Regards,

Arpit

Re: Quality Management Datasources

Former Member — Thu, 27 Mar 2014 10:48:02 GMT

Hi,

I am able to see the inspection lots in QALS table but the same inspection Lot is not updating into my Datasources 2LIS_05_QE1 and QE2.

Whenever we do the usage decision for particular inspection Lot it is updating into the Datasource 2LIS_05_QVUDN.

Please guide.

Regards,

Kavitha

Re: Quality Management Datasources

former_member186399 — Thu, 27 Mar 2014 11:01:59 GMT

Dear Kavitha

Can you check whether there is an entry in the table QAMR for the inspection lot. If yes then only it will appear in QE1 & QE2

Regards

Gajesh

Re: Quality Management Datasources

former_member182343 — Thu, 27 Mar 2014 11:14:25 GMT

HI,

Not able to see data even in full load ?