Question Re: No conversion between FT3 and LB found during WO confirm in Supply Chain Management Q&A

No conversion between FT3 and LB found during WO confirm

Former Member — Mon, 21 Mar 2016 12:01:05 GMT

Dear Experts,

I am getting below error during Warehouse order confirmation.

No conversion between FT3 and LB found

Message No. /SCWM/HUFUNCTIONS121

Please find warehouse number control settings for my warehouse

Weight Unit LB Time Unit MIN

Volume Unit FT3 Unit of Length FT

Currency USD Factory Calend. US

Please advise what I am wrong. and when I am debug the conversion happening twice.

Step1) KG, LB

Step2) LB, FT3(failed)

Please advise.

Regards,

Vadamalai A.

Re: No conversion between FT3 and LB found during WO confirm

former_member183610 — Mon, 21 Mar 2016 12:12:38 GMT

Hi,

Did you maintain the conversions in the product master unit of measurement view? Transaction /SAPAPO/MAT1

should have to maintain the conversion from one unit of measurement to other alternate

unit of measurements.

C K REDDY

Re: No conversion between FT3 and LB found during WO confirm

Former Member — Mon, 21 Mar 2016 14:54:11 GMT

Hi Reddy,

Thanks for your quick reply and I have made changes in product master however still I am getting the same error. Please find below screenshot form EWM product master.

Can you please advise if I did anything wrong and any changes required in product master level.

Please.

Regards,

A Vadamalai.

Re: No conversion between FT3 and LB found during WO confirm

Former Member — Mon, 21 Mar 2016 15:06:00 GMT

Hi,

Adding detailed log during WT creation for wave item.

Error during WT creation for wave item MC00 5 1

***** Product WT Creation *****

For wave 5 1

For warehouse request PDO 5272 10

For product FERT-02@ERP001; quantity 1,00000000000000 EA

***** Determine source data - start *****

Determining source data with storage type:, section:, bin:, HU:

Storage type search fully defined: No entry found

Storage type search with wild card: Search sequence PK01 and rule FIFO found

Determine stock in source storage type 0150

Determine stock in source storage bin 0150-01-01-03

Storage bin 0150-01-01-03 is not assigned to any physical inventory area

Source storage bin 0150-01-01-03 determined in storage type 0150

***** Determine destination data - start *****

Defaults for destination data: StorType:9099 Storage Sec.:0001 Stor. Bin:GI-ARE

Destination storage type 9099 checked successfully

Destination storage section 0001 is entered in storage type: 9099

Alternatives during bin search: 1st alt. Stor.Bin Type, 2nd alt. Storage Sec., 3rd alt. StorType

Access table for bin search:

Storage type: 9099 storage section: 0001 bin type: whse pos. eval.: 00000

Start of destination bin search

Stor.type: 9099, stor.area: 0001, bin type: , stock mvmt: 00000 being examined

Storage type 9099: HUs allowed but not required

Standard putaway behavior (storage type 9099)

Capacity check against storage bin GI-AREA

Weight: 41 LB are checked

against free capacity 999.999.999.999,999 KG with tolerance 0 KG

Volume: 495 FT3 are checked

against free capacity 999.999.999.999,999 LB with tolerance 0 LB

No conversion between FT3 and LB found

No warehouse task created

***** Start wave release for wave MC00 5

***** Wave release division step started for wave MC00 5

One wave read

No warehouse tasks were created for wave MC00 5

Re: No conversion between FT3 and LB found during WO confirm

former_member183610 — Mon, 21 Mar 2016 15:43:51 GMT

Hi,

Could you maintain the two separate lines for unit of measurement conversions and check .

1. EA to LB

2. LB to FT3.

C K REDDY

Re: No conversion between FT3 and LB found during WO confirm

JuergenPitz — Mon, 21 Mar 2016 16:40:33 GMT

Hi,

I do not think that you have to maintain any conversions. But something seems to be setup wrong.

Your log shows:

Weight: 41 LB are checked --> this comes from the item.

against free capacity 999.999.999.999,999 KG with tolerance 0 KG --> this comes from the bin. In here it says that the unit is KG. And the system is ok with it. But in your first mail you wrote:

"Please find warehouse number control settings for my warehouse

Weight Unit LB"

And according to this message I would say that the first information is wrong.

Then the log continues

Volume: 495 FT3 are checked --> again, this comes from the item.

against free capacity 999.999.999.999,999 LB with tolerance 0 LB --> and now this is where your error comes from. Because it says the volume unit in the bin is LB. And of course there is no system conversion from FT3 to LB.

Your first mail says

"Please find warehouse number control settings for my warehouse

Weight Unit LB Time Unit MIN

Volume Unit FT3 Unit of Length FT"

But according the log I would say - no, it is maintained differently. Or did you maybe make changes? And the bins were created before with wrong information? Can you show a screenshot of a bin?

Brgds

Juergen

---

Want to learn EWM?

Check for EWM courses @ https://training.sap.com/curriculum/scm_ewm

Get a SAP Learning Hub Subscription: https://training.sap.com/shop/learninghub

Re: No conversion between FT3 and LB found during WO confirm

Former Member — Tue, 22 Mar 2016 02:11:37 GMT

Hi Pitz,

Yes, the issues seems to be at Bin level. Please find below screenshot and can you help me what its wrong?

I have created the bin after the product master.

and I ran the report /SCWM/RWEIGHT_VOLUME_UPDATE as well but still my issue is exist.

Regards,

A Vadamalai

Re: No conversion between FT3 and LB found during WO confirm

JuergenPitz — Tue, 22 Mar 2016 08:45:41 GMT

Hi,

actually according the screenshot everything is setup ok. Is this really the bin GI-AREA?

If the issue persists, I would delete the bin, check the settings on warehouse number level, re-create the bin.

But actually the report you mentioned should straighten out everything...

Brgds

Juergen

Re: No conversion between FT3 and LB found during WO confirm

former_member317963 — Wed, 08 Apr 2020 11:13:15 GMT

Did you find solution on the same? i am facing same issue.

error as below:

No conversion between F and M found

Message No. /SCWM/HUFUNCTIONS121

Re: No conversion between FT3 and LB found during WO confirm

former_member317963 — Mon, 25 May 2020 09:00:47 GMT

I have found the resolution as below: -

In warehouse number control unit of length is maintained: 'M'. I changed it to 'FT' it is resolved. So the volume unit and unit of length should be in the same unit of measure. earlier it was in cubit foot and meter. it should be in foot and cubic foot/meter and cubic meter.