Question Re: PREPARE_JSPM_QUEUE phase. in Enterprise Resource Planning Q&A

PREPARE_JSPM_QUEUE phase.

Former Member — Sun, 18 Sep 2011 06:55:49 GMT

Dear All

I am stuck on PREPARE_JSPM_QUEUE phase, the error is paste below.

I have notice in SLD / SMSY patches are same of SAP_JTECHF, SAP_JTECHS,CORE-TOOLS AND LM-TOOLS but i went to source system to determine the patch level are slightly difference

The Stack calculate on based of SMSY.

SLD / SMSY :::: SOURCE SYSTEM

SAP_JTECHF...............7.00.6 :::: 7.00.6.2

SAP_JTECHS...............7.00.6 :::: 7.00.6.1

CORE-TOOLS...............7.00.6 :::: 7.00.6.3

LM-TOOLS....................7.00.6 :::: 7.00.6.0

this is the reasons that validation of the deploy queue was not successful. Validation of queue sapjup-queue completed with error The stack does not match the system. Probably the system was changed after the stack was generated.

Please advise how to correct the issue.

Regards

Anwer Waseem

SAP NetWeaver

Edited by: Anwer Waseem on Sep 18, 2011 9:56 AM

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Sun, 18 Sep 2011 11:16:17 GMT

Hi,

As I understand, the SLD is not getting updated with the latest SP/patch information from the source system.

Suggest you to check the SLD Data Supplied bridge in the Visual Administrator of the Source system. Check the SLD host and port settings and trigger the data supply. Ensure you get a success message.

Next on the SolMan SLD, check the technical system information for the source java system. Also the last updated date and time should correspond to the above data supply trigger. Once the SP/patches are updated here, then start the smsy_setup tcode to populate the SMY with updated values from the SLD.

Regards,

Srikishan

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Sun, 18 Sep 2011 11:53:00 GMT

Dear Srikishan

Actually I don't have problem to transfer component and system data to SLD . JAVA and ABAP are transferring succfully to SLD server as per scheduled.

The Problem is here that Source system component release and SLD + SMSY are not matchting the JAVA level;

source system having compoennt CORE-TOOLS 700 SP6 ( 1000.7.00.6.3)

SLD and SMSY having component CORE-TOOLS 700 SP6 ( 1000.7.00.6.0)

This is the difference which is getting problem during EHPI running on java side.

How will i get equal of source and SLD+SMSY so that, i can smoothly continue the java configuartion process in EHPI ?

Regards

Anwer Waseem

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Sun, 18 Sep 2011 17:15:30 GMT

Hi Anwer,

I assume the below:

Even though the SLD data transfer trigger from Java source system to SolMan SLD works fine, the SLD shows incorrect values. Also the last updated values of the Java source technical system in SLD is the latest.

If so, then I could suggest removing the SLD Java technical system and Java system in the SMSY. And perform a fresh trigger into the SLD - just to check if the fresh trigger brings in the most current patch level information. Ofcourse this depends on if the technical is used in SLD configuration and if the SMSY entries is used in SolMan related configuration.

Regards,

Srikishan

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Sun, 18 Sep 2011 18:42:22 GMT

Hello

I did two times to delete the System including abap and java from the SLD and SMSY then trigger to refresh data to SLD

its come with same setting;

should i modify the stack xml file for that component to enter manuall changes. ?

Advise Please

Regards

Anwer Waseem

SAP NetWeaver

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Mon, 19 Sep 2011 10:23:14 GMT

Hi,

What is target patch level that you want to upgrade ?

Thanks

Sunny

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Mon, 19 Sep 2011 10:59:41 GMT

Dear Sunny

Its encluded EHP2 for SAP NetWeaver 7 SP stack 8 (06/2011) while i calculate patches of EHP5.

Ofcourse, i want to upgrade by the above given SP stack 8.

Regards

Anwer Waseem

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Fri, 13 Jan 2012 10:39:46 GMT

Dear All,

Did any one find the Solution for this issue?, because even I too facing the same issue.

I Syched the JAVA stack information to central SLD and LMDB, but still SMSY not showing the patch level.

Regards,

Kumar

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Fri, 13 Jan 2012 12:46:38 GMT

Hello,

Please check Note 1469745 :

"In the stack configuration file remove the tags <target-system></target-system> with everything between them, and then restart the tool."

If it not helps, please check Note 1399846 also.

Regards,

Laszlo

Re: PREPARE_JSPM_QUEUE phase.

Former Member — Mon, 06 Feb 2012 10:47:45 GMT

The provided Note 1469745 got worked, Thanks