topic Re: Dynamic Selection screen modification in Application Development and Automation Discussions

Dynamic Selection screen modification

Former Member — Fri, 11 Jul 2008 05:20:26 GMT

Hi,

I have two radio buttons R_A and R_B and 2 parameters P_A and P_B on selsection screen

When i click on R_A , P_A should be visible ---> It Works

When i click on R_B , P_B should be visible ---> It Works

But after clicking on R_B if i click on R_A, then P_B is visble and P_A is not visible.

How should i go abt this.???

Re: Dynamic Selection screen modification

former_member156446 — Fri, 11 Jul 2008 05:22:12 GMT

in the at selection-screen output event.. your will find a logic like..

loop at screen.

some code ".. this is responsible for these changes.. look there..

endloop.

Re: Dynamic Selection screen modification

former_member673464 — Fri, 11 Jul 2008 05:24:24 GMT

hi,

I think you have forget to write the code for the first radio button for changing the properties of the p_a.

Regards,

Veeresh

Re: Dynamic Selection screen modification

Former Member — Fri, 11 Jul 2008 05:26:27 GMT

hi,

when you are checking the condition of Radio Button 1 then inside that plz check for the other parameter visibility. And if that is visible plz make it invisible.

Repeat this process for both the Radio BUttons.

I think that will solve your problem.

Regards

Sumit Agarwal

Re: Dynamic Selection screen modification

Former Member — Fri, 11 Jul 2008 05:28:29 GMT

Hey!!

Check out this sample code.


REPORT z_sdn.
 
PARAMETERS:
  p_num RADIOBUTTON GROUP rad1 DEFAULT 'X' USER-COMMAND abc,
  p_char RADIOBUTTON GROUP rad1.
 
PARAMETERS:
  p_num1 TYPE i MODIF ID num,
  p_num2 TYPE i MODIF ID num,
  p_char1 TYPE c MODIF ID chr,
  p_char2 TYPE c MODIF ID chr.
 
 
AT SELECTION-SCREEN OUTPUT.
  IF p_num EQ 'X'.
    LOOP AT SCREEN.
      IF screen-group1 EQ 'CHR'.
        screen-active = 0.
        MODIFY SCREEN.
      ENDIF.
    ENDLOOP.
  ELSE.
    LOOP AT SCREEN.
      IF screen-group1 EQ 'NUM'.
        screen-active = 0.
        MODIFY SCREEN.
      ENDIF.
    ENDLOOP.
  ENDIF.

Regards

Abhijeet Kulshreshtha

Re: Dynamic Selection screen modification

Former Member — Fri, 11 Jul 2008 05:34:26 GMT

HI,

Chk this:

Selection-screen begin of block b1 WITH FRAME NO INTERVALS.
Parameters: s1 radiobutton group g1 user-command u1 default 'X',
            p_name(10) MODIF ID M1,
            p_email(20) MODIF ID M1,
            s2 radiobutton group G1.
Parameters: p_name1(10) MODIF ID M2,
            p_fax(10) MODIF ID M2.
 Selection-screen end of block b1 .

AT SELECTION-SCREEN OUTPUT.
*  IF S_BOX = 'X'.
      LOOP AT SCREEN.
      IF SCREEN-GROUP1 = 'M3'.
        SCREEN-ACTIVE = '0'.
        MODIFY SCREEN.
      ELSE.
        SCREEN-ACTIVE = '1'.
        MODIFY SCREEN.
      ENDIF.
    ENDLOOP.

*  ENDIF.

  IF S1 = 'X'.
    LOOP AT SCREEN.
      IF SCREEN-GROUP1 = 'M2'.
        SCREEN-ACTIVE = '0'.
        MODIFY SCREEN.
      ELSEIF SCREEN-GROUP1 = 'M1'.
        SCREEN-ACTIVE = '1'.
        MODIFY SCREEN.
      ENDIF.
    ENDLOOP.
  ELSEIF S2 = 'X'.
    LOOP AT SCREEN.
      IF SCREEN-GROUP1 = 'M1'.
        SCREEN-ACTIVE = '0'.
        MODIFY SCREEN.
      ELSEIF SCREEN-GROUP1 = 'M2'.
        SCREEN-ACTIVE = '1'.
        MODIFY SCREEN.
      ENDIF.
    ENDLOOP.
  ENDIF.

regards,

madhumitha

Re: Dynamic Selection screen modification

Former Member — Fri, 11 Jul 2008 05:51:25 GMT

Hi Sap User,

refer to the code below:

parameters:
  p_a type c modif id aaa,
  p_b type c modif id bbb,
  r_a radiobutton group rad default 'X' user-command x,
  r_b radiobutton group rad.

at selection-screen output.

if r_a = 'X'.
  loop at screen.
   if screen-group1 = 'BBB'.
    screen-active = 0.
    screen-invisible = 1.
    modify screen.
   endif.
   endloop.

elseif r_b = 'X'.

  loop at screen.
   if screen-group1 = 'AAA'.
    screen-active = 0.
    screen-invisible = 1.
    modify screen.
   endif.
   endloop.
endif.

With luck,

Pritam.