topic Re: OAHEX in Application Development and Automation Discussions

OAHEX

Former Member — Wed, 21 Dec 2005 17:18:21 GMT

Hi,

When I execute program OAHEX in 5.0 I don't get any output while the same program in 4.5B works correctly. Has anybody come across this problem?

Thanks,

Anuranjan

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:20:56 GMT

HI Anuranjan Sharma,

I'm on 5.0 and its working for me.Can you see that program in se38??

Regards,

Ravi

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:22:19 GMT

Hi Ravi,

This is the coding I have:

REPORT OAHEX .

PARAMETER: INPUT(2) DEFAULT 'A' LOWER CASE.

DATA: MAX_X TYPE X VALUE '80',

OUTPUT(2),

BEGIN OF X,

X TYPE X,

END OF X,

P TYPE P,

HEX TYPE X.

*MOVE INPUT TO X. MOVE INPUT TO HEX.

MOVE X-X TO OUTPUT.

MOVE X-X TO P.

WRITE: 'Eingabewert'(001), AT 20 'Hexadezimal'(002),

AT 40 'Dezimal'(003), AT 60 'Zuweisung'(004).

ULINE.

WRITE: INPUT, AT 20 OUTPUT, AT 40 P LEFT-JUSTIFIED, AT 60 HEX.

What is it there in urs?

Thanks a lot for quick reply

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:23:41 GMT

Is your Unicode checks active or not in the attributes for that program?

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:25:22 GMT

Yes it's active.

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:25:27 GMT

Hi,

It is exactly the same here too.

What did you mean when you say it is not working correctly?

Regards,

Ravi

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:27:53 GMT

When I enter A as input out I get is:

Output of hexadecimal values

Input Value Hexadecimal Decimal Assgmt

A 00 0 00

While in 4.5 it works like this

Input value Hexadecimal Decimal Assgmt

A 41 65 A0

Only difference in coding is line

move input to x. move input to hex.

is not commented in 4.5

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:28:07 GMT

Hi it is working for me...

but giving no values..

vijay

Message was edited by: Vijay Babu Dudla

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:29:29 GMT

Vijay, R u on 5.0 and do u have the output same as I have shown above for 4.5.

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:31:00 GMT

it is not giving output as in 4.7

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:32:32 GMT

Hi Sharma,

When I do a EPC for that program, it says,

The namespace of the program OAHEX has the setting "C" and cannot be tested

A possible cause for this is that an SAP program is being checked in a customer

system

Note, the following rule applies after a change in the source code:

For testing the namespace setting is ignored for one week

(The message cannot be hidden using pseudo-comment "#EC .., bzw. durch SET

EXTENDED CHECK OFF/ON)

Probably it is a reason.

Regards,

ravi

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:35:28 GMT

Hi Sharma,

The line in bold is the reason.

REPORT OAHEX .

PARAMETER: INPUT(2) DEFAULT 'A' LOWER CASE.

DATA: MAX_X TYPE X VALUE '80',

OUTPUT(2),

BEGIN OF X,

X TYPE X,

END OF X,

P TYPE P,

HEX TYPE X.

<b>*MOVE INPUT TO X. MOVE INPUT TO HEX.</b>

MOVE X-X TO OUTPUT.

MOVE X-X TO P.

WRITE: 'Eingabewert'(001), AT 20 'Hexadezimal'(002),

AT 40 'Dezimal'(003), AT 60 'Zuweisung'(004).

ULINE.

WRITE: INPUT, AT 20 OUTPUT, AT 40 P LEFT-JUSTIFIED, AT 60 HEX.

Probably it is commented for some reason by SAP.

See if it uncommented in 4.5.

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:37:20 GMT

Hi Ravi,

U mean to say SAP is still working on this and we should wait till they fix it.

Thanks,

Anuranjan

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:38:55 GMT

Hi Sharma,

I ran the program in 46C and got the result you got in 45 and I ran it in 47 and got the result you got for 5. The difference between the two is as Ravi pointed out. The line "MOVE INPUT TO X. MOVE INPUT TO HEX." is commented out in the higher version and it is not in the lower version.

Srinivas

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:38:56 GMT

Exactly. May be it will be fixed in the next Patch level.

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:40:39 GMT

Hi Srinivas,

So I should open a message with SAP right?

Thanks,

Anuranjan

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:40:55 GMT

What are you using this for? It is a simple program, which probably you can also copy and uncomment those lines. I don't know if SAP is going to work on this or fix. May be it is intended to work this way.

Srinivas

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:42:07 GMT

i tried uncommenting, it is throwing some errors..

and if you really want that then you can copy it from 4.7

and use it..

vijay

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:43:31 GMT

I did a where-used on the program and it is not used anywhere.

Re: OAHEX

Former Member — Wed, 21 Dec 2005 17:44:22 GMT

Hi Srinivas,

I tried that first but the commneted line causes syntax error.

thanks

Anuranjan