topic GETWA_NOT_ASSIGNED_RANGE in Application Development and Automation Discussions

GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 07:16:37 GMT

DEAR GURUS,

I am getting a runtime error GETWA_NOT_ASSIGNED_RANGE in a function module. The code extraction is in the below.

Please provide me a solution.

IT IS IN ECC 6.0.

code extraction is below:-

LOOP AT loc_detail.

ASSIGN loc_str+loc_detail-offset(loc_detail-leng) TO <fsvar>.

CONCATENATE 'INT_DATA_' loc_tab INTO fs_string-table.

MOVE '-' TO fs_string-hy.

MOVE loc_detail-fieldname TO fs_string-field.

CONDENSE fs_string NO-GAPS.

ASSIGN (fs_string) TO <fsvar1>.

runtime error >>>>>MOVE <fsvar> TO <fsvar1>.

ENDLOOP.

Please help me.

Thanks

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 07:27:25 GMT

This message was moderated.

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 07:37:32 GMT

please help me.

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 07:43:47 GMT

HI,

Are you on a Unicode enabled system? If yes, pl verify if the SAP Note No. 900669 is relevant in your scenario.

Regards,

Hari

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 07:54:46 GMT

Hi Ravi,

What is the FM you are using? or In which program/tcode u got this Runtime error?

I am searching some OSS notes to give you solution.

Regards,

Hari

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 08:02:55 GMT

Thanku very much,

It is Z function module.

Thanks and Regards

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 08:10:48 GMT

Hi Ravi,

If it is a ZFunction module ...then no need to look for OSS Notes.

I think the problem lies in the data declaration of <fsvar> and <fsvar1>. I feel both are of different types...so when moving from field to other field ...there is some mismatch ...check the declarations once.

Regards,

Hari

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 08:18:02 GMT

dear Hari,

thanku very much,

both are declared as type any.

if data is not there it is running , other wise it is givi n g short dump,

Thanks and Regards,

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 08:24:47 GMT

Can you please paste the entire code ?

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 08:29:04 GMT

This is the actual code

Message was edited by:

Ravi Kumar Kuntala

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 12:19:33 GMT

please help me

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Wed, 12 Sep 2007 12:22:32 GMT

Hi,

Have you declared <fsvar> like <fsvar1>.

This dump is because of non declaraton of the field symbols

declare the symbols propelry

Regards

Shiva

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Thu, 13 Sep 2007 06:37:15 GMT

I have declared correctly.

please help me

Thanks in advance

Re: GETWA_NOT_ASSIGNED_RANGE

Former Member — Thu, 25 Oct 2007 13:24:12 GMT

Hi Ravi,

Found any solution?

I am also facing the same problem and it is bit urgent.