topic Re: partner profile in Application Development and Automation Discussions

partner profile

Former Member — Thu, 13 Sep 2007 11:44:09 GMT

What is the difference between generate partner profile and creat partner profile ?

Re: partner profile

Former Member — Thu, 13 Sep 2007 11:50:24 GMT

Create Partner ProfilesAlthough partner profiles are usually created automatically, because of the unusual inbound and outbound profiles needed on the same system, the manual generation of certain profiles is required.

The following subsections describe the partner profile settings for the standard client (assumed here to be ALExxxCyyy), as well as for the corresponding dummy client (assumed to be DUMxxxCyyy). The dummy client partner profiles should have been generated by the automatic generation process completed previously. Nevertheless, these should be checked to ensure that all profiles exist.

Generation of Partner Profiles

The following messages should be added to the 4xx-ORDR model for ALExxxCyyy to DUMxxxCyyy on the reference client:

• ORDERS

• ORDCHG

• ZINVRV

• ORDRSP

• INVOIC

• FIDCMT

• The partner profiles should first be generated using the standard auto-generation procedure on the reference client (for SYNCH messages to be created).

• This model should now be distributed to the both ALExxxCyyy and DUMxxxCyyy.

• The partner profiles should now be generated on the client being configured (i.e. yyy) using the auto-generation procedure defined in the standard ALE configuration procedures.

Generate partner profiles for sending system. (Can only do this if at least 1 message type exists against the sending system's LS). This automatically generates the port if the LS and RFC name are the same.

generate partner profiles tcode BD82

creating partner profiles tcode WE20

 There are two methods for maintaining the partner profile:

 Maintain partner profile manually:

To navigate to the partner profile in the sender system, choose Partner profile -> Partner type of Logical System and click on the required Target system. Under Outbound parameters, choose the Create outbound parameters icon, and enter the values for the outbound parameters according to the slide Sender: Partner Profile (outbound).

To navigate to the partner profile in the sender system, choose Partner profile -> Partner type of Logical System and click on the required Sending system. Under Inbound parameters, choose the Create inbound parameters icon and enter the values for the inbound parameters according to the slide Sender: Partner Profile (inbound).

 Generate partner profile:

Prerequisite: The current distribution model is distributed to all participating systems.

In the sender system, choose: Generate Partner Profile, then check the result in the partner profile (outbound)

In the sender system, choose: Generate Partner Profile, then check the result in the partner profile (inbound)

Regards

Vasu

Re: partner profile

varma_narayana — Thu, 13 Sep 2007 11:52:35 GMT

Hi Mithun.

Generate Partner Profile ( Tcode BD82 ) : Here the System generates the Partner profiles automatically. But

1) This is possible only in ALE since the Partner type Must be LS

2) The RFC Destination must have the Same name as Target Logical system

Create partner profile : (Tcode WE20)

Here we can Create or Modify the Partner profiles manually.

reward if Helpful

Re: partner profile

Former Member — Thu, 13 Sep 2007 12:06:31 GMT

Hi,

Normally when u r going to create distribution model by using BD64 the sys will generates the partner profile automatically only when in ALE and the Partner type Must be LS(Logical sys)

2) The RFC Destination must have the Same name as Target Logical system

<b>Create partner profile : (Tcode WE20)</b> :

--To navigate to the partner profile in the sender system, choose Partner profile -> Partner type of Logical System and click on the required Target system. Under Outbound parameters, choose the Create outbound parameters icon, and enter the values for the outbound parameters according to the slide Sender: Partner Profile (outbound).

-- To navigate to the partner profile in the sender system, choose Partner profile -> Partner type of Logical System and click on the required Sending system. Under Inbound parameters, choose the Create inbound parameters icon and enter the values for the inbound parameters according to the slide Sender: Partner Profile (inbound).

Here we can Create or Modify the Partner profiles manually.

<b>Reward with points if helpful.</b>

Regards,

Vijay