topic Re: sm35 in Application Development and Automation Discussions

sm35

Former Member — Fri, 04 May 2007 05:53:40 GMT

Hi All.

I have an issue in the sm35.

I created a session ,while processing I selected the session and clicked on process.it has given a pop up screen .asking for fore/back ground.those things are ok.

but the additional functions like Extended mode,Expert mode........

Can any body help me to get the documentation for this additional functions.

Exatly my requirement is, if in my session 10 transcations are there,if error occurs on 4 th transcation then

1. I want to terminate the session with out processing the remaining.(i.e from 5th to 10 th)

2.up to 3 rd transcation I want to roll back with out posting too.

Thanks in advance,

regards,

eswar

Re: sm35

Former Member — Fri, 04 May 2007 06:00:42 GMT

Do you process 10 transactions in asingle session in real scenario?

I don't imagine..

See the doc:

Extended log for batch input processing

EXPERT MODE

Activate expert mode in interactive batch input

Expert mode only works in interactive batch input.

You can activate it when processing a batch input session, or with the function:

System->Services->Batch Input->Expert mode

Expert mode deactivates Error Message 344, i.e. you can branch from batch input without constantly being told 'Batch input data not available for this screen'.

Set standard size of dynpros before session processing

The interactive batch input generally only runs with screens that are

present in their standard characteristics.

Increasing or decreasing the size of the screen, either before or during processing, can cause errors.

The additional function 'Standard screen size' resets the screen to its

standard size during processing.

Checkbox: Cancel if Log Error Occurs During Batch Input

The system stopped processing the batch input session after the current transaction caused an error, using the addition function Cancel if Log Error Occurs.

You can change the value of this indicator using the SAP profile parameter bdc/protocol/errorforceend'.

Reward points if useful

Regards

Anji

Re: sm35

andreas_mann3 — Fri, 04 May 2007 06:07:58 GMT

hi,

1. better use call transaction than creating bdc

so you can terminate your processing

2. <b>not possible</b> or you must do all checks and validations in your own program (in a simulation of your transaction)

Message was edited by:

Andreas Mann

Re: sm35

Former Member — Thu, 07 Jun 2007 00:02:13 GMT

Hi eswar,

any luck on this...we hv similar issue.

cheers!

Re: sm35

Former Member — Thu, 07 Jun 2007 00:09:23 GMT

use bdcmsgcoll strucure in call transaction ,if msgtype is E,then use exit command.

2.up to 3 rd transcation I want to roll back with out posting too.

This is not possible

Message was edited by:

Seshu Maramreddy

Re: sm35

Former Member — Thu, 07 Jun 2007 00:28:00 GMT

Hello Venkat,

I have simple solution since roll back is not possible.

assume that you have data at Internal table

start-of-selection.

loop at i_data. " i_data is the file data.

here you have bdcdata.

call transaction tcode using bdcdata

mode 'N'

messages into i_bdcmsg . " i_bdcmsg is BDCMSGCOLL

loop at i_bdcmsg.

select single * t100 into t100

where with i_bdcmsg.

if you see msgtype is 'E'.

exit. " it will go end-of-selection and displays log data ,here you will find out how many records updated,based on that you can remove those records in input file.

else

i_log-field = i_data-field.

i_log-text = 'message from t100 table'.

endloop

endloop.

end-of-selection.

here you diplaying or downloading log data.