topic Re: Regarding reports in Application Development and Automation Discussions

Regarding reports

Former Member — Tue, 27 Feb 2007 07:16:01 GMT

In an interactive report, after going to 5th list, can you come back to 2nd list? How?

Re: Regarding reports

seshatalpasai_madala — Tue, 27 Feb 2007 07:20:05 GMT

Hi,

By setting the sy-lsind you can get back to the list corresponding to that index.

You can manipulate the sy-lsind field.

Regards,

Sesh

Re: Regarding reports

Former Member — Tue, 27 Feb 2007 07:33:25 GMT

hi,

Set sy-lsind = 5.

or Try this.

DATA: l TYPE i, t(1) TYPE c.

DO 100 TIMES.

WRITE: / 'Loop Pass:', sy-index.

ENDDO.

TOP-OF-PAGE.

WRITE: 'Basic List, Page', sy-pagno.

ULINE.

TOP-OF-PAGE DURING LINE-SELECTION.

WRITE 'Secondary List'.

ULINE.

AT LINE-SELECTION.

DESCRIBE FIELD sy-lisel LENGTH l IN CHARACTER MODE

TYPE t.

WRITE: 'SY-LSIND:', sy-lsind,

/ 'SY-LISTI:', sy-listi,

/ 'SY-LILLI:', sy-lilli,

/ 'SY-CUROW:', sy-curow,

/ 'SY-CUCOL:', sy-cucol,

/ 'SY-CPAGE:', sy-cpage,

/ 'SY-STARO:', sy-staro,

/ 'SY-LISEL:', 'Length =', l, 'Type =', t,

/ sy-lisel.

IF SY-LSIND = 15.

SY-LSIND = 5.

ENDIF.

WRITE: 'SY-LSIND:', sy-lsind,

/ 'SY-LISTI:', sy-listi,

/ 'SY-LILLI:', sy-lilli,

/ 'SY-CUROW:', sy-curow,

/ 'SY-CUCOL:', sy-cucol,

/ 'SY-CPAGE:', sy-cpage,

/ 'SY-STARO:', sy-staro,

/ 'SY-LISEL:', 'Length =', l, 'Type =', t,

/ sy-lisel.

_______________________

try Sy-LSIND to 5.

____________________________________________

In the logic

case sy-lsind

when lsind = 15

Code

sy-lsind = 5.

endcase.

pls : award points

sri

Re: Regarding reports

Former Member — Tue, 27 Feb 2007 07:35:55 GMT

hi murali,

AT LINE-SELECTION.

case sy-lsind.

when 5.

sy-lsind = 2.

endcase.

regards,

priya.

Re: Regarding reports

Former Member — Tue, 27 Feb 2007 07:41:01 GMT

Hi Priya,

Supoose can i put back button in each list,Means it will go the previous list.In that button whcih event i have to write the code.

Re: Regarding reports

Former Member — Tue, 27 Feb 2007 07:46:38 GMT

hi murali,

if u have created a button then write the logic under AT USER-COMMAND.

data: v_ucomm type sy-ucomm.

v_ucomm = sy-ucomm.

AT USER-COMMAND.

CASE V_UCOMM.

when 'BACK'.

ENDCASE.

do reward if it helps,

priya.

Re: Regarding reports

Former Member — Tue, 27 Feb 2007 07:58:36 GMT

Thamku very much for solving theproblem.