topic Re: reports in Application Development and Automation Discussions

reports

Former Member — Thu, 14 Dec 2006 05:08:03 GMT

Hi all,

i got one code like

START-OF-SELECTION.

PERFORM GET_DATA1.

if it_ekko[] is initial.

message e000(e4) with 'Service data not available for the Purchase document'.

*set screen 1000.

else.

PERFORM GET_DATA.

PERFORM PROCESS_DATA.

PERFORM DISPLAY_DATA.

endif.

if i give the code like this wht happens is if i_ekko is empty i will get an error screen apart from selection-screen saying tht 'Service data not available for the Purchase document'

My requirement is

I want to get the message 'Service data not available for the Purchase document' in the same selection-screen.Pls give me a logic for this with a sample code.

Thanks in advance

Re: reports

Former Member — Thu, 14 Dec 2006 05:11:46 GMT

Hi,

If you want to get this is selection screen then

specify ...your code in AT SELECTION SCREEN event

AT SELECTION-SCREEN.

PERFORM GET_DATA1.

if it_ekko[] is initial.

message e000(e4) with 'Service data not available for the Purchase document'.

*set screen 1000.

endif.

START-OF-SELECTION.

PERFORM GET_DATA.

PERFORM PROCESS_DATA.

PERFORM DISPLAY_DATA.

*REWARD if this helps

Re: reports

Former Member — Thu, 14 Dec 2006 05:12:10 GMT

message e000(e4) with 'Service data not available for the Purchase document'

in this message if u use S000(e4) ur message will be displayed in the same screen in the status bar.

if u use I000(e4) u will get a pop up in the same screen

Re: reports

Former Member — Thu, 14 Dec 2006 05:12:11 GMT

message S000(e4) with 'Service data not available for the Purchase document'.

JUs write 'S' instead of E.

U will get it.

Please mark points if useful.

Re: reports

Former Member — Thu, 14 Dec 2006 05:12:36 GMT

Hi ,

What i understand is that you want to get the selection screen back so that you can execute the program with another set of data .

If my understanding is correct , then test the condition in AT SELECTION-SCREEN event.

try this code


AT SELECTION-SCREEN 
PERFORM GET_DATA1.
if it_ekko[] is initial.
message e000(e4) with 'Service data not available for the Purchase document'.
*set screen 1000.
ENDIF

START-OF-SELECTION.


PERFORM GET_DATA.
PERFORM PROCESS_DATA.
PERFORM DISPLAY_DATA.
endif.

In case of query please revert back.

Regards

Arun

Reward point if found helplful

Re: reports

Former Member — Thu, 14 Dec 2006 05:12:38 GMT

Hi Alex,

Use

message S(e4) with 'Service data not available for the Purchase document'.

S- for status

Regards,

Vivek

Reward if helps.

Re: reports

Former Member — Thu, 14 Dec 2006 05:16:18 GMT

hi...

give the code as follows..

START-OF-SELECTION.

PERFORM GET_DATA1.

if it_ekko[] is initial.

message e000(e4) .

*set screen 1000.

else.

here i've jus removed that.. with 'Service data not available for the Purchase document'..after ur error message.

try it this way. else it's better for u to give as a information msg rather than error msg,as i've given below.

try:

START-OF-SELECTION.

PERFORM GET_DATA1.

if it_ekko[] is initial.

message i000(e4) . "give the message as an information message.

*set screen 1000.

else.

by giving as information msg, it'll pop up in the selction screen itself. once enter,again ur selction parameters becomes available for u to enter ur inputs.

'Service data not available for the Purchase document' is wat u hav mentioned in ur message class rite(beside e4)!!

try all this..

if useful,reward points.

all the best.