topic New to SapScript in Application Development and Automation Discussions

New to SapScript

Former Member — Mon, 04 Dec 2006 16:21:22 GMT

I have never used SapScripts before to apologise if this question is a stupid one. How to I check if a field is 0? I have written the following code but it doesn't seem to recognise that the field is 0:

IF &VBDPR-FKIMG& = 0.000

Any help would be greatly recieved.

Kind Regards

Carly

Re: New to SapScript

Former Member — Mon, 04 Dec 2006 16:28:43 GMT

Use

IF &VBDPR-FKIMG& IS INITIAL.

CODE...

ENDIF.

Regs

Manas Ranjan Panda

Re: New to SapScript

Former Member — Mon, 04 Dec 2006 16:52:05 GMT

Hi,

/: IF &VBDPR-FKIMG& = '0.000'

/: ENDIF.

Regards

Sudheer

Re: New to SapScript

Former Member — Mon, 04 Dec 2006 16:52:26 GMT

I have changed the code to

IF &VBDPR-FKIMG& IS INITIAL

and I get the following message:

An error occurred in the text command IF. A parameter is too long.

The command line was ignored.

Can anyone help?

Regards

Carly

Re: New to SapScript

Former Member — Mon, 04 Dec 2006 17:01:40 GMT

I have also tried


/: IF &VBDPR-FKIMG& = '0.000'
E1  Carly,,
/: ELSE
/: other code
/: ENDIF

but when the field is 0.000 it is just moving onto the other code instead of writing Carly.

Regards

Carly

Re: New to SapScript

Former Member — Mon, 04 Dec 2006 17:06:33 GMT

Hi Bond,

Put 0.000 in single qotes. it will work.

Thanks

Vikrnath Khimavath

Message was edited by:

Khimavath Vikranth

Re: New to SapScript

Former Member — Tue, 05 Dec 2006 09:55:07 GMT

This is my code:

/:   IF &VBDPR-FKIMG& = '0.000'                                              
E1   	Carly,,                                                                
/:   ELSE
/:              Other Code.........
/:ENDIF

When the field &VBDPR-FKIMG& is 0.000 it doesn't write Carly is just goes into the ELSE statement.

Has anyone got any other ideas as single quotes have not worked?

Cheers

Carly

Re: New to SapScript

Former Member — Tue, 05 Dec 2006 10:09:28 GMT

Hi ,

try this way.

IF not &VBDPR-FKIMG& is initial .

ur code.

else .

ur code

endif.

Regards

SAntosh

Re: New to SapScript

Former Member — Tue, 05 Dec 2006 10:30:00 GMT

HI,

TRY THIS.

/: IF &VBDPR-FKIMG& = ' 0.000'

Carly

/: ELSE

OTHER

/: ENDIF

TRY TO DEBUG THE FORM AND SEE THAT FIELD COPY THE VALUE WITH SPACES AND PASTE IT WITHIN THE QUOTES AND TRY IT AGAIN.

Message was edited by:

Manoharsairam Kavuri

Message was edited by:

Manoharsairam Kavuri

Re: New to SapScript

Former Member — Tue, 05 Dec 2006 10:38:19 GMT

Thank you Manoharsairam Kavuri, that worked. The code should have been

IF &VBDPR-FKIMG& = '            0.000'

Regards

Carly

Re: New to SapScript

Clemenss — Tue, 05 Dec 2006 11:06:04 GMT

Hi,

IS INITIAL is nonsense. This is ABAP, not SapScript.

Switch on the DEBUG mode from SE71, set a break point to the element where &VBDPR-FKIMG& is output.

Put the symbol &VBDPR-FKIMG& to the symbols at the bottom. Check what the contents is like when it is 0.

Probably there is no 0.000 but just spaces. The the IF statement should be

IF &VBDPR-FKIMG& = ' '

Regards,

Clemens