topic selection screen validation in Application Development and Automation Discussions

selection screen validation

Former Member — Wed, 06 Dec 2006 08:37:22 GMT

hi all,

in selection screen i have 6 fields , 2 push buttons . when i click on first button . first three fields must be enabled and remaining buttons must be disabled . and if i click on second pushbutton first three fields must be disabled and remaining should be enable how can i do that.

thnx in advance

Re: selection screen validation

Former Member — Wed, 06 Dec 2006 08:39:15 GMT

hi Amar,

Put Your Logic at <b>AT SELECTION-SCREEN OUTPUT</b>. event ..

Regards,

Santosh

Re: selection screen validation

Former Member — Wed, 06 Dec 2006 08:42:45 GMT

use AT-SELECTION SCREEN OUTPUT

Re: selection screen validation

Former Member — Wed, 06 Dec 2006 08:43:23 GMT

Hi amar,

Check this link, ur requirement is similar to this:

It will help u.

Here u can find code also.

Regards,

Kumar

Message was edited by:

kumar kk

Re: selection screen validation

Former Member — Wed, 06 Dec 2006 08:47:10 GMT

In AT SELECTION-SCREEN OUTPUT event.

If OK_CODE eq 'BUT1'.

LOOP AT SCREEN.

IF SCREEN-NAME = 'TEXT1'.

disable it.

ENDIF.

IF = 'TEXT2'

disable

same for text3.

ENDLOOP.

ELSEIF OK_CODE EQ 'BUT2'..

LOOP AT SCREEN.

IF = TEXT4.

disable.

endif.

write other conditions.

ENDLOOP.

ENDIF.

Regards

Surya.

Re: selection screen validation

jayanthi_jayaraman — Wed, 06 Dec 2006 08:47:11 GMT

Hi,

p1(10) modif id Z1,

p2(10) modif id z2,

p3(10) modif id z3,

p4(10) modif id z4,

p5(10) modif id z5,

p6(10) modif id z6.

SELECTION-SCREEN PUSHBUTTON /1(24) name USER-COMMAND Button1.

SELECTION-SCREEN PUSHBUTTON /2(24) name USER-COMMAND Button2.

AT SELECTION-SCREEN output.

LOOP AT SCREEN.

IF ( sscrfields-ucomm = 'BUTTON1' and ( SCREEN-GROUP1 = 'Z1' or

SCREEN-GROUP1 = 'Z2' or SCREEN-GROUP1 = 'Z3' ) ) or

( sscrfields-ucomm = 'BUTTON2' and ( SCREEN-GROUP1 = 'Z4' or

SCREEN-GROUP1 = 'Z5' or SCREEN-GROUP1 = 'Z6' ) ).

SCREEN-input = 1.

ELSE.

SCREEN-input = 0.

ENDIF.

MODIFY SCREEN.

ENDLOOP.

Kindly reward points if it helps.

Re: selection screen validation

Former Member — Wed, 06 Dec 2006 08:53:44 GMT

Hi Amar

I hope below code will give you some idea:

parameters: p_fld1(10) type c,
            p_fld2(10) type c,
            p_fld3(10) type c,
            p_fld4(10) type c,
            p_fld5(10) type c,
            p_fld6(10) type c.
selection-screen begin of line.
selection-screen pushbutton:  (5) but1 user-command ABC,
                            15(5) but2 user-command DEF.
selection-screen end of line.

data: f_3 type i value 1,
      l_3 type i.

at selection-screen output.
  loop at screen.
     case screen-name.
     when 'P_FLD1' or 'P_FLD2' or 'P_FLD3'.
          screen-active = f_3.
     when 'P_FLD4' or 'P_FLD5' or 'P_FLD6'.
          screen-active = l_3.
     endcase.
     modify screen.
  endloop.

at selection-screen.
  if sy-ucomm = 'ABC'.
     f_3 = 1.
     l_3 = 0.
  elseif sy-ucomm = 'DEF'.
     f_3 = 0.
     l_3 = 1.
  endif.

initialization.
  move: 'BUT1' to but1,
        'BUT2' to but2.

Kind Regards

Eswar