topic Re: dynamic display in table control in Application Development and Automation Discussions

dynamic display in table control

Former Member — Tue, 26 Dec 2006 04:33:01 GMT

hi all,

i hav an issue regarding Module Pool programming. i wnt 2 disply table control with dynamic enteries both at header level and the content level, ie. the values of the heading shud com 4m an internal table and the values a user enters shud go 2 another internal tab. i cannot take the values of one column of d tab contrl in a diff internal tab n so on for all headers.

Re: dynamic display in table control

Former Member — Tue, 26 Dec 2006 04:48:38 GMT

CAn you be more clear?

What i understand from your question is----

You want to display values (header level) from one internal table and the values entered in the table control should go into another internal table is that what you mean?

if thats the thing

First to diaplay values from 1 internal table...you do it in PBo of the screen

The values you have to store from the table control shold be written in PAI event of the screen.

One thing i like to know, how you are planning to move from table control. Is user selecting those rows in table control and after an event( like save or just entering) and moving it to another intenal table.

Please be more clear as what you want to do?

Regards

Re: dynamic display in table control

Former Member — Tue, 26 Dec 2006 05:26:15 GMT

i tell u the scenario, the user enters a delivery no. in d frst screen n in d nxt screen the reults shws total no of material in dat del no. in the header of the tab cntrl, nw the user'll enter serial no of each material in dat particular column. so dependng upon the materials in a del no. totl no of columns'll b displayed. and 'n' numbr of serial no. cn b entrd. So individually for evry material i need all serial no in one int tab n so on (or it cud b in one int tab also). this reult i hav 2 pass in a BDC prog for tcode IQ02 for changing the status of each serial no of a material. The prob i m facing is i m nt abl to get the entries a user enters in the tab contrl in an int tab although i hav displayed the header bt i cannot tk the values enterd by the user.there is no save or ny odr command d user is entering jst a single button 2 chng d status aftr entering all seril no. I hop dis'll hlp u 2 undrstnd d prob.

reply.

Re: dynamic display in table control

Former Member — Tue, 26 Dec 2006 05:41:49 GMT

in the flow logic , in process after output add the following lines.

PROCESS AFTER OUTPUT.

*suppose gt_final is the table wich is holding the material and their serial numbers.

loop at gt_final.

FIELD gt_final-matnr MODULE pick_sel.

endloop.

in the module pick_sel add this lines...

MODULE pick_sel INPUT.

if not gt_final-serialNo is initial.

MODIFY gt_final INDEX tab_cntl-current_line TRANSPORTING matnr

serialNo.

ENDIF.

ENDMODULE. " pick_sel INPUT

hope this works! if not let me know

Regards

Re: dynamic display in table control

Former Member — Tue, 26 Dec 2006 07:24:55 GMT

srry i think m nt abl 2 explain d prob compltly 2 u. i dont hav any intrnal tab where both material and serial no. exists. serial no'll com from user input and material no from a delivery no. this combination i wnt in a int tab. i hav alrdy declared a loop for matnr for header, is it possible to hav 2 loops in both PBO n PAI. n its not 4 one material bt for n materials in dat particular del.no. so wat'll b the declaration for dat int tab gt_final.

secondly if i tak materils in gt_final then it'll run for say 5 times for 5 materials,

( dis loop,

loop at gt_final.

FIELD gt_final-matnr MODULE pick_sel.

endloop.

)

den hw cn i transport 50 seril no for 1 material in gt_final.

plz ask if u didnt gt it.

thnx

Re: dynamic display in table control

Former Member — Tue, 26 Dec 2006 09:44:08 GMT

I am bit confused over here?

You are displaying material number for the said delivery number.

Say for one delivery number you are displaying 10 material numbers.

tell me this are you using table control to feed in the serial number for the material numbers or not.

i am assuming tht you are using the table control to display material number in 2nd screen after you enter delvery number in initial screen.

So for all material numbers displayed you are entering serial numbers in table control.

screen 1

Delivery Number

Screen 2

mat1 srno1

mat1 srno2

mat2 srno3

mat3 srno3

and after that you want to update the internal table which has all three fields delv No, Mat no and srno.

Is that what you are doing.

Revert back

Re: dynamic display in table control

Former Member — Tue, 26 Dec 2006 11:14:13 GMT

See dis ‘ll b design format,

Screen 1 delivrry no._________

In PAI it’ll find total no. of material no. n other details.

Screen 2. (header) matnr1 matnr2 matnr3……(cmng from int tab 1 on which d loop is defined in PBO of screen 2)

Ser1 Ser2 Ser3 (entered by the user)

Ser11 Ser22

Ser12 ……

button( to tk this combination in one int table in the followng format for running it in BDC)

matnr1 Ser1

matnr1 Ser11

matnr1 Ser12

matnr2 Ser2

matnr2 Ser22

matnr3 Ser3

revert if nt clear

Re: dynamic display in table control

Former Member — Wed, 27 Dec 2006 02:52:02 GMT

How you are linking serial numbers to material.....? if material number is in header, how you are trying to link which serial number belongs to which material...are you doing it in table control?