topic Re: regarning warning message in Application Development and Automation Discussions

regarning warning message

Former Member — Tue, 17 Oct 2006 06:04:10 GMT

I have created a selection screen report.

after giving warning message, i have to put back control to main screen.

If i am raising a warning message, it is giving an error and control is going to blank screen.

how to put control on main screen?

Re: regarning warning message

anversha_s — Tue, 17 Oct 2006 06:07:09 GMT

hi,

its better to give the message type as 'I'.

message 'check this answer' type 'I'.

rgds

anver

if hlpful pls mark points

Re: regarning warning message

anversha_s — Tue, 17 Oct 2006 06:07:17 GMT

hi,

its better to give the message type as 'I'.

message 'check this answer' type 'I'.

rgds

anver

if hlpful pls mark points

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:08:34 GMT

A Warning message will not stop the execution of the report further.

1. You will have to issue a ERROR Message

2. Issue a warning message and then use a STOP statement or use the EXIT statement.

Regards,

Ravi

Note : Please mark all the helpful answers

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:12:50 GMT

I have written statements as follows:-

MESSAGE 'Selection was not restricted.' TYPE 'W'.

STOP.

Stop is in the code. but the warning message is not putting on the main screen.

Re: regarning warning message

gopi_narendra — Tue, 17 Oct 2006 06:15:10 GMT

warning type does not stop u at the screen, its just a warning that will prompt u and will continue.

so better give a ERROR type message

Regards

- Gopi

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:18:12 GMT

In my case, Error and warning both are putting me on the blank screen. I wanted to put the control back to main screen.

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:20:27 GMT

Can you post the code please?

Regards,

Ravi

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:28:18 GMT

start-of-selection.

*If the Selection Crieteria specified

IF S_BUDAT[] is not initial OR

S_BWART[] is not initial.

Do processing

else. "Give Warning message

MESSAGE 'Selection was not restricted.' TYPE 'W'.

endif. "Selection Criteria

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:33:45 GMT

start-of-selection.

*If the Selection Crieteria specified

IF S_BUDAT[] is not initial OR

S_BWART[] is not initial.

Do processing

else. "Give Warning message

MESSAGE 'Selection was not restricted.' TYPE 'W'.

EXIT.

endif. "Selection Criteria

Add the EXIT as shown.

Regards,

Ravi

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:35:52 GMT

simple, try like below.

MESSAGE W....... WITH '....'.

CALL SCREEN <SCR NUM>.

<SCR NUM> SHOULD BE THE SCRREN NUMBER OF THE SAME SCREEN WHICH U WANT TO BE IN.

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:43:41 GMT

Both EXIt and call screen are not putting me back to main screen.

Re: regarning warning message

Former Member — Tue, 17 Oct 2006 06:46:49 GMT

oh,

with warning message ?& error message, current program will be terminated , so u cannot call back ur screen.

so, only solution would be , try changing it to status or info message if possible.

Re: regarning warning message

Former Member — Fri, 24 Nov 2006 08:07:41 GMT

we can put back the control to main screen by putting warning message in

at selection-screen event rather then start-of-selection.