topic Re: Set values to standard transaction fields in Application Development and Automation Discussions

Set values to standard transaction fields

Former Member — Thu, 27 Jul 2006 12:48:36 GMT

Hi,

I am trying to set values to a standard transaction by my program using set parameter id. But, while calling the transaction, i think somewhere the values I passed is getting refreshed and no values are appearing in the called transaction!

Is there any other way through which I can pass the values and set the fields with them?

Please help.

Thanks & Regards,

Anshumita.

Re: Set values to standard transaction fields

Former Member — Thu, 27 Jul 2006 12:53:30 GMT

Hi,

please cross check the field in the screen painter ; is it enable for SET / GET parameter ID.

u can also check the value of the PARAMETER ID in debuging mode.

start debugging the program.

goto~~->system area~~->sap memmory

search the PARAMETER id and check the corresponding value.

here u can see the value set for the parameter id.

if u can see the value then field is not enabled for

get/set parameter.

Please Reward Points & Mark Helpful Answers

To mark Helpful Answers ;click radio Button next to the post.

RadioButtons

o Helpful Answer

o Very helpful Answer

o Problem Solved.

Click any of the above button next to the post; as per the anwers

To close the thread; Click Probelm solved Radio Button next to the post , which u feel is best possible answers

Message was edited by: Manoj Gupta

Re: Set values to standard transaction fields

naimesh_patel — Thu, 27 Jul 2006 12:53:45 GMT

hello,

Another way is by making small BDC ... just pass whatever you want to that screen.

CALL TRANSACTION 'MM02' WITH BDCTAB MODE 'A'.

Regards,

Naimesh

Re: Set values to standard transaction fields

Former Member — Thu, 27 Jul 2006 12:54:39 GMT

Please go through this link...

http://help.sap.com/saphelp_nw2004s/helpdata/en/9f/db9e0435c111d1829f0000e829fbfe/content.htm

Regards,

Amit.

Re: Set values to standard transaction fields

Former Member — Thu, 27 Jul 2006 13:05:54 GMT

Hi,

I there is problem with SET PARAMETER ID, then check whether you have correctly specified the PARAMETER ID fields for the Transaction.

Ex:

DATA REPID like sy-repid VALUE 'RSPFPAR'.

SET PARAMETER ID <b>'RID'</b> FIELD REPID.

Else try doing a partial BDC recording for that transaction using Transaction recorder(SHDB).

Check this sample code using Partial BDC for Transaction MD48


 REPORT zztest.

DATA : it_mara TYPE STANDARD TABLE OF mara WITH HEADER LINE,
       layout TYPE rm61m-usprf.

DATA:   bdcdata LIKE bdcdata    OCCURS 0 WITH HEADER LINE.


START-OF-SELECTION.

  layout = 'SAPMPS'.
  SELECT * FROM mara INTO TABLE it_mara UP TO 2 ROWS.

  LOOP AT it_mara.


    PERFORM bdc_dynpro      USING 'SAPMM61M' '0103'.
    PERFORM bdc_field       USING 'BDC_OKCODE'
                                  'TCAL'.

    PERFORM bdc_field       USING 'RM61M-MATNR'
                                  it_mara-matnr.
    PERFORM bdc_field       USING 'RM61M-USPRF'
                                  layout.
    CALL TRANSACTION 'MD48'

    USING bdcdata
    MODE   'A'.

  ENDLOOP.



*----------------------------------------------------------------------*
*        Start new screen                                              *
*----------------------------------------------------------------------*
FORM bdc_dynpro USING program dynpro.
  CLEAR bdcdata.
  bdcdata-program  = program.
  bdcdata-dynpro   = dynpro.
  bdcdata-dynbegin = 'X'.
  APPEND bdcdata.
ENDFORM.                    "BDC_DYNPRO

*----------------------------------------------------------------------*
*        Insert field                                                  *
*----------------------------------------------------------------------*
FORM bdc_field USING fnam fval.

  CLEAR bdcdata.
  bdcdata-fnam = fnam.
  bdcdata-fval = fval.
  APPEND bdcdata.

ENDFORM.                    "BDC_FIELD

Regards,