topic Re: reg va01 bdc program in Application Development and Automation Discussions

reg va01 bdc program

Former Member — Tue, 20 Jun 2006 07:43:44 GMT

hi to all

while running bdc i am getting rabax

Unable to interpret "/" as a number.

The program attempted to interpret the value "/" as a number, but since the value contravenes the rules for correct number formats, this was not possible

i am trying to pass kwmeng value to bdcdata

i found this error

how to correct this error

regards

vijay

Re: reg va01 bdc program

Former Member — Tue, 20 Jun 2006 07:50:22 GMT

Hi,

1. You cannot pass a special character to a number field. Some how you need get your data right.

2. Why are you not using a BAPI for this. BAPI_SALESORDER_CREATEFROMDAT2

Regards,

Ravi

Note : <REMOVED BY MODERATOR - REQUEST OR OFFER POINTS ARE FORBIDDEN>

Edited by: Alvaro Tejada Galindo on Aug 15, 2008 4:50 PM

Re: reg va01 bdc program

dani_mn — Tue, 20 Jun 2006 07:51:13 GMT

You are passing '/' into a number field.

Get the name of the field from your dump analysis and correct it into the upload program. pass the correct value to this field.

Regards,

Wasim Ahmed

Re: reg va01 bdc program

Former Member — Tue, 20 Jun 2006 07:58:06 GMT

Hi,

is the error coming from KWMENG or FROM ANY DATE field.

i doubt the error is from the Data not with the BDC.

check your Data is going correctly into ITAB while uploading from PC or Application server.

Regards

vijay

Re: reg va01 bdc program

Former Member — Tue, 20 Jun 2006 08:04:52 GMT

hi vijay

while debugging

i found error when assigning value from internal table (item table ) to bdc_feild

loop at it_item where kuagv eq it_header-kuagv.

*perform bdc_field using 'BDC_CURSOR'

'RV45A-MABNR(01)'.

concatenate 'RV45A-MABNR(' n ')' into mabr.

part of my progrom.

perform bdc_field using mabr

it_item-mabnr.

*perform bdc_field using 'RV45A-KWMENG(01)'

it_item-kwmeng.

concatenate 'RV45A-kwmeng(' n ')' into kmeng.

perform bdc_field using kmeng

it_item-kwmeng.

(am facing problem here)

concatenate 'RV45A-werks(' n ')' into werk.

*perform bdc_field using 'VBAP-WERKS(01)'

it_item-werks.

perform bdc_field using werk

it_item-werks.

perform bdc_dynpro using 'SAPMV45A' '4001'.

perform bdc_field using 'BDC_OKCODE'

'=ITEM'.

regards

vijay

Re: reg va01 bdc program

Former Member — Tue, 20 Jun 2006 08:04:55 GMT

If you're using the std routines of BDC program BDCRECX1, here there's a control to set NO_DATA value in the bcd table:

FORM BDC_FIELD USING FNAM FVAL.

IF FVAL <> NODATA.

CLEAR BDCDATA.

BDCDATA-FNAM = FNAM.

BDCDATA-FVAL = FVAL.

APPEND BDCDATA.

ENDIF.

ENDFORM.

If FVAL is number your dump'll occur.

So you should transfer the numaber value to char variable:

PERFORM BDC_FIELD USING <FIELD> NUMBER.

Max

DATA: NUMBER(20) TYPE C.

WRITE KWMENG UNIT <UNIT> TO NUMBER.

Re: reg va01 bdc program

Former Member — Tue, 20 Jun 2006 08:13:32 GMT

perform bdc_field using kmeng

it_item-kwmeng

what is the value in it_item-kwmeng.

and are you using BDCRECX1 then in the selection screen provide No Data Indicator as '/'.

Regards

vijay

Re: reg va01 bdc program

Former Member — Fri, 15 Aug 2008 09:51:50 GMT

declare that field as type c in declaration part.

Re: reg va01 bdc program

Former Member — Fri, 15 Aug 2008 10:25:09 GMT

Use the BAPI for creating sales orders instead - it is a much better approach than old-fashioned BDC's.