topic Re: Project User status update in Application Development and Automation Discussions

Project User status update

Former Member — Thu, 29 Oct 2015 12:27:48 GMT

Hello experts - I am using the following BAPI's inorder to update the project user status.

CALL FUNCTION 'BAPI_PS_INITIALIZATION'.

CALL FUNCTION 'BAPI_BUS2001_SET_STATUS'

CALL FUNCTION 'BAPI_PS_PRECOMMIT'

CALL FUNCTION 'BAPI_TRANSACTION_COMMIT'

I am getting subrc 0 after execution of CALL FUNCTION 'BAPI_BUS2001_SET_STATUS' , But getting a dump in BAPI_PS_PRECOMMIT .

From ST22 , I could see the pointer is on the redline .

The termination occurred in ABAP program "SAPLPS_BAPI", in "CHK_PRECOMMIT".The main program was "RS_TESTFRAME_CALL".

FORM chk_precommit.

DATA: chk_precommit_ok TYPE c,
chk_error type c.

CALL FUNCTION 'PS_FLAG_GET_GLOBAL_FLAGS'
       IMPORTING
            e_precommit_ok = chk_precommit_ok
            e_error        = chk_error.

IF chk_precommit_ok = space.
*   Precommit wurde noch nicht aufgerufen.
    MESSAGE x030(cnif_pi).
ELSEIF chk_precommit_ok <> 'Y'.
*   Precommit wurde nicht erfolgreich durchlaufen.
    MESSAGE x033(cnif_pi).
elseif not chk_error is initial.
*   At least one single BAPI failed
    MESSAGE x056(cnif_pi).
ENDIF.

Any idea on how to get rid of this ?

Thanks,

Arun.

Re: Project User status update

RaymondGiuseppi — Thu, 29 Oct 2015 12:47:27 GMT

You are using BAPI so a

I am getting subrc 0 after execution of CALL FUNCTION 'BAPI_BUS2001_SET_STATUS'

is not relevant, don't check sy-subrc but analyze RETURN table for any error message (TYPE = 'E' or 'A') at each level that returns it so BAPI + PRE COMMIT + COMMIT (if WAIT) and don't execute next step in this case.

Regards,

Raymond

Re: Project User status update

Ankit_Maskara — Thu, 29 Oct 2015 13:05:23 GMT

Hello Arun,

As suggested by Raymond, check the return table of all the BAPIs. It may be a configuration issue which does not allow to change the status of a project user. Also have you tried manually to change the status of a project user.

BR.

Re: Project User status update

Former Member — Fri, 30 Oct 2015 04:16:35 GMT

My Return table is empty here , Any more leads pls ?

Re: Project User status update

Former Member — Fri, 30 Oct 2015 04:18:00 GMT

I am able to change the values in Front end but not through BAPI , My return table is empty and subrc is 0 after the BAPI call 'BAPI_BUS2001_SET_STATUS'.

Thanks,

AJ.

Re: Project User status update

Ankit_Maskara — Fri, 30 Oct 2015 05:15:56 GMT

AFAIK, BAPIs only simulate what has been configured meaning if you can change via GUI/T-code then you can change via BAPIs also. So you may be missing out some BAPI/FM. I am not sure about exact BAPI/FM but one more check you can do is to Test all the BAPI's in sequence in SE37 and see if you are successful there.

I still think you are missing call to some BAPI/FM in your codebase and should re-check once the entire Function Group.

BR.

Re: Project User status update

RaymondGiuseppi — Fri, 30 Oct 2015 07:19:57 GMT

Read 1901102 - Short dump MESSAGE_TYPE_X , this error is usually raised when sequence of call is not correct.

Hint: Also look at returned table E_RESULT too for more information than single record in RETURN parameter (this is not a table parameter in BAPI_BUS2001_SET_STATUS definition)

Regards,

Raymond

Re: Project User status update

Former Member — Fri, 30 Oct 2015 09:00:08 GMT

You are a life saviour . Thanks a ton.

Closing the thread as answered.

Regards,

AJ.