OTF end command // missing in OTF data

Former Member — Fri, 22 May 2015 14:28:26 GMT

Hi Expert,

i m new to smartforms..I m facing a problem in smartforms while converting into pdf. when i run the program I am getting the information message "OTF end command // missing in OTF data". I have used the following function modules.

ALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'

EXPORTING

formname = c_payslip_form

IMPORTING

fm_name = lv_fm_name

EXCEPTIONS

no_form = 1

no_function_module = 2

OTHERS = 3.

IF sy-subrc = 0.

lwa_control_parameters-no_open = abap_true.

lwa_control_parameters-no_close = abap_true.

*kanishka

CALL FUNCTION 'SSF_OPEN'

EXPORTING

output_options = lwa_output_options

control_parameters = lwa_control_parameters

EXCEPTIONS

formatting_error = 1

internal_error = 2

send_error = 3

user_canceled = 4

OTHERS = 5.

IF sy-subrc <> 0.

* Implement suitable error handling here

ENDIF.

LOOP AT pit_payslip_header INTO lwa_payslip_header.

READ TABLE pit_payslip_item INTO lwa_payslip_item INDEX sy-tabix.

CALL FUNCTION lv_fm_name

EXPORTING

control_parameters = lwa_control_parameters

output_options = lwa_output_options

wa_header_data = lwa_payslip_header-header

IMPORTING

job_output_info = it_otf_data

TABLES

it_item_data = lwa_payslip_item-item

EXCEPTIONS

formatting_error = 1

internal_error = 2

send_error = 3

user_canceled = 4

OTHERS = 5.

IF sy-subrc <> 0.

MESSAGE ID sy-msgid TYPE 'S' NUMBER sy-msgno DISPLAY LIKE 'E'

WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.

LEAVE LIST-PROCESSING.

ENDIF.

it_otf_data = it_otf_data.

AT LAST.

CALL FUNCTION 'CONVERT_OTF'

EXPORTING

format = 'PDF'

IMPORTING

bin_filesize = bin_filesize

TABLES

otf = it_otf_final

lines = it_pdfdata[].

CALL FUNCTION 'SX_TABLE_LINE_WIDTH_CHANGE'

EXPORTING

line_width_dst = '255'

TABLES

content_in = it_pdfdata[]

content_out = it_pdf[].

IF sy-subrc = 0.

* "Send mail

* PERFORM send_mail.

ENDIF.

ENDAT.

ENDLOOP.

Re: OTF end command // missing in OTF data

SwadhinGhatuary — Tue, 26 May 2015 09:36:47 GMT

Hi Kanishka,

Until unless u close the smart form by ssf_close the otf will not capture .

take one entry in internal table and cross check this.

Re: OTF end command // missing in OTF data

suraj_meda — Fri, 29 May 2015 07:30:53 GMT

Hi Kanishka,

Are you passing the right internal table " it_otf_final" or " it_otf_data". to FM 'CONVERT_OTF'

Because i see the statement " it_otf_data = it_otf_data.",

If you are trying to convert the entire OTF data in the loop, can use the statement like:

"append lines of it_otf_data to it_otf_final"

Regards,

Suraj

Re: OTF end command // missing in OTF data

gregorygotera — Mon, 01 Jun 2015 13:09:12 GMT

You should mark the parameter GETOTF inside the CONTROL_PARAMETERS table.

Regards

Gregory

topic OTF end command // missing in OTF data in Application Development and Automation Discussions

OTF end command // missing in OTF data

Re: OTF end command // missing in OTF data

Re: OTF end command // missing in OTF data

Re: OTF end command // missing in OTF data