topic Re: Pricing FM std variable xkomv-kawrt issue in Application Development and Automation Discussions

Pricing FM std variable xkomv-kawrt issue

Former Member — Wed, 21 Aug 2013 06:08:47 GMT

Dear All,

My requirement is to call single subroutine of Pricing FM - xkomv_bewertenthrough Z report program to calculate net price of a material. For that, I am passing material quantity as 1 to KOMP-MGAME as below:

DATA: c_1 TYPE komp-mgame VALUE 1.

komp-mgame = c_1.

Along with other field-values of KOMP variable and other required variables, I am calling PERFORM xkomv_bewerten from my Z program. All these structures / variables are declared in Std. SAP Top Include "lv61atop". I have included that top-include in my Z program.

In debug, I found this issue:

1. Go to Include "LV61AA74" (Form konditionsbasis_ermitteln) and put a breakpoint at line no. 141 as shown below:

2. Go to VA01. Provide basic details - Order type, sales org, dist channel, division, sold-to, ship-to, material, quantity as 1, and press enter. It will start the debugger and set below values for variables:

3. While from my Z program, if I set KOMP-MGAME = 1, and then call PERFORM xkomv_bewerten, it will set variables as below in debug mode at the same code location:

4. Error is: XKOMV-KAWRT is set to 1.00 (Hex Value 100C)while calling from Z program. It should be set to 10.00 (Hex Value 1000C) as per VA01 runtime values.

Observation / Analysis:

All the relevant variables for this issue are declared in Std. SAP code (top – include). I have included the same in my Z program. So declaration could not be the reason for this error.
After setting initial values, the program flow executes std. SAP code with no enhancement / exits implemented. So enhancements / exits cannot be a reason for this error.
Error giving statement: “xkomv-kawrt = arbfeld_dec.” is a simple assignment statement from std. SAP code. It converts 1.000 (type p decimals 3 ) to 10.00 (type WERTV8 <decimals 2>) because of variables’ nature of definition.

Please suggest if you have any clue about the solution.

Thanks in advance,

Birwa

Re: Pricing FM std variable xkomv-kawrt issue

vamsixk — Wed, 21 Aug 2013 08:32:36 GMT

Hi Birwa,

I had faced a similar Issue while trying to load pricing condition values for contracts.

According to my analysis based on the condition type -calculation type, a division by 10 is carried out.(refer to attached screenshot)

Am not sure functionality wise why this happens, but i have only analyzed it technically. Please check for yourselves. hope the screenshot helps.

Regards

Vamsi

Re: Pricing FM std variable xkomv-kawrt issue

Former Member — Wed, 21 Aug 2013 12:15:16 GMT

The problem is due to fixed point arithmethic.

The main program for RV64* does not has this active try removing it fromyour program too..

Or find an FM that can return the value for you.

For more details refer to my blog.

Re: Pricing FM std variable xkomv-kawrt issue

Former Member — Thu, 22 Aug 2013 05:25:08 GMT

Hi Vamsi,

Thanks for your reply. I have checked the code you attached and tried to put a breakpoint in it to analyze in detail, but VA01 / Pricing FM did not call this functionality at all. Can you please share how this screen shot-code is related to VA01 pricing calculations?

Thanks again,

Birwa

Re: Pricing FM std variable xkomv-kawrt issue

Maciej_DomagaBa — Thu, 22 Aug 2013 12:33:07 GMT

See SE80: function group V61A properties:

Note the option highlighted above and set it the same way in your Z-program (SE80-> Goto-> Properties).

regards

Re: Pricing FM std variable xkomv-kawrt issue

Former Member — Fri, 23 Aug 2013 06:18:32 GMT

Hey Maciej,

Thanks, it solved my issue. I was stuck at this place since long. Thanks a lot!

Regards,

Birwa