topic Re: Input parameter is not save after selection. Please help! in Application Development and Automation Discussions

Input parameter is not save after selection. Please help!

Former Member — Tue, 20 Aug 2013 15:47:41 GMT

Hi all,

I am writing a report that read two inputs parameters. These are obligatory.

SELECTION-SCREEN BEGIN OF BLOCK 1 WITH FRAME TITLE text-005.

PARAMETERS: name(40) type c OBLIGATORY.

PARAMETERS: nr type i OBLIGATORY.

SELECTION-SCREEN END OF BLOCK 1.

AT SELECTION-SCREEN ON VALUE-REQUEST FOR name.

............

Perfom XXXX.

Perform YYY.

What am I doing wrong?

I can select the first parameter from the help list without problem. When I enter the second one, I can see that the variable is empty after setting a break point and going in the debug mode.

What should I do to make this work? Please help.

Re: Input parameter is not save after selection. Please help!

Arun_Prabhu_K — Wed, 21 Aug 2013 03:15:43 GMT

Hello Maria Margy.

Refer this thread http://scn.sap.com/thread/840861.

Regards.

Re: Input parameter is not save after selection. Please help!

former_member209120 — Wed, 21 Aug 2013 04:22:07 GMT

Hi Maria Margy,

I tried like this, I am getting values can you share your code to check what's the problem.

DATA       : r_name TYPE TABLE OF ddshretval WITH HEADER LINE.
DATA       : BEGIN   OF   t_name OCCURS 0,
              name   TYPE char40,
              END     OF   t_name.

SELECTION-SCREEN BEGIN OF BLOCK 1 WITH FRAME TITLE text-005.
PARAMETERS:   name(40) type c OBLIGATORY.
PARAMETERS:   nr type i OBLIGATORY.
SELECTION-SCREEN END OF BLOCK 1.
AT SELECTION-SCREEN ON VALUE-REQUEST FOR name.
REFRESH t_name.
   APPEND 'Ramesh' TO t_name.
   APPEND 'Ganesh' TO t_name.

   CALL FUNCTION 'F4IF_INT_TABLE_VALUE_REQUEST'
     EXPORTING
       retfield        = 'NAME'
       dynpprog        = sy-repid
       dynpnr          = '1000'
       dynprofield     = 'name'
       window_title    = 'Name'
       value_org       = 'S'
     TABLES
       value_tab       = t_name[]
       RETURN_TAB      = r_name[]
     EXCEPTIONS
       parameter_error = 1
       no_values_found = 2
       OTHERS          = 3.
   IF sy-subrc <> 0.
   ENDIF.

start-of-SELECTION.

Write :/ name, nr.

Re: Input parameter is not save after selection. Please help!

SujeetMishra — Wed, 21 Aug 2013 04:25:31 GMT

Hi Maria,

ELECTION-SCREEN BEGIN OF BLOCK 1 WITH FRAME TITLE text-005.

PARAMETERS: name(40) type c OBLIGATORY.

PARAMETERS: nr type i OBLIGATORY.

SELECTION-SCREEN END OF BLOCK 1.

AT SELECTION-SCREEN ON VALUE-REQUEST FOR name.

............

If below perform is not used for screen level validation then please use it in start of selection event.

START-OF-SELECTION.

Perfom XXXX.

Perform YYY.

Regards,

Sujeet

Re: Input parameter is not save after selection. Please help!

Former Member — Wed, 21 Aug 2013 04:38:08 GMT

Hi Maria,

To get the values input at the selection screen,

you can try the FM,

CALL FUNCTION 'DYNP_VALUES_READ'

EXPORTING

dyname = sy-repid "Program name

dynumb = sy-dynnr "screen number

TABLES

dynpfields = gt_dynfields "fields on selection screen

EXCEPTIONS

OTHERS = 01.

IF sy-subrc = 0.

READ TABLE gt_dynfields INTO gs_dynfields WITH KEY fieldname = 'NAME'.

IF sy-subrc = 0.

gv_name = gs_dynfields-fieldvalue.

ENDIF.

Regards,

Shruti D

Re: Input parameter is not save after selection. Please help!

Former Member — Wed, 21 Aug 2013 05:00:52 GMT

Hi Maria,

Please check if after the FM is executed you are assigning a value to the selection screen parameter. Also

use a data type for deifining a parameter .

Thanks

Asha

Re: Input parameter is not save after selection. Please help!

Former Member — Wed, 21 Aug 2013 21:02:01 GMT

Thanks for your answer. Is it possible to define an intervall for the parameter

PARAMETERS: nr type i OBLIGATORY.

I would like that only number for example between 0 and 1000 can be enter by the user.

Thanks

Re: Input parameter is not save after selection. Please help!

former_member209120 — Thu, 22 Aug 2013 07:34:30 GMT

Hi Maria Margy,

Use select options and put validation

DATA : var TYPE i.

SELECT-OPTIONS : s_var FOR var OBLIGATORY.

AT SELECTION-SCREEN ON s_var.
   IF ( s_var-low NOT BETWEEN '0' AND '1000' ) AND ( s_var-high NOT BETWEEN '0' AND '1000' ).
     MESSAGE : 'Please enter vale between 0 to 100' TYPE 'E'.
   ENDIF.