topic Re: If condition failed in Application Development and Automation Discussions

If condition failed

Ranjith_D_Reddy — Mon, 24 Jun 2013 07:51:09 GMT

We are facing one issue in the below mentioned code

As per debugging the value we are passing in V_REM =13

But the control is executing the code in line Num:1327 .Actually the condition should fail as per the value passed ,but in this case it is not happening.

regards,

ranjith.

Re: If condition failed

matt — Mon, 24 Jun 2013 08:12:23 GMT

What is the type of v_rem? And I assume you mean line 1328 is being executed?

Note: 4 without quotes is not the same as '4'

Re: If condition failed

former_member209120 — Mon, 24 Jun 2013 08:24:49 GMT

Hi Ranjith,

Use if condition like this, it should be clear to analyze.

data : a(4) type C,
        b(4) type C,
        c(4) type C.

a = 10.
b = 11.
c = 12.

if a gt 4 and a le 10.
   Write : 'Hi 4'.
elseif a gt 11 and a le 20.
   Write : 'Hi 9'.
endif.

What every you used if condition totally confusing, please make if condition like above and try, you will get answer .

Re: If condition failed

former_member188827 — Mon, 24 Jun 2013 08:30:13 GMT

what is the value in "EX_MVGR3"? Line no 1327 will be processed as system would check the "if" condition but control should not go to 1328 in your case.

Regards

Re: If condition failed

Former Member — Mon, 24 Jun 2013 08:40:21 GMT

Hi Ranjith,

Check yr code for if condition to some part u did not passed in single quote.

Kindly check it.

Thanks.

Pavan.N

Re: If condition failed

former_member196490 — Mon, 24 Jun 2013 08:47:01 GMT

what is the data type of V_REM. Remove the quotes from '5.5' and try again

Re: If condition failed

Ranjith_D_Reddy — Mon, 24 Jun 2013 08:58:05 GMT

This message was moderated.

Re: If condition failed

Ranjith_D_Reddy — Mon, 24 Jun 2013 08:58:06 GMT

Acutually we are making use of the decimal number to compare in the IF condition as '5.5'

Re: If condition failed

matt — Mon, 24 Jun 2013 09:02:42 GMT

Are you saying that v_rem is defined as a decimal? What is the EXACT data type?

Re: If condition failed

Ranjith_D_Reddy — Mon, 24 Jun 2013 09:07:56 GMT

Thanks !Matthew's we are using the CHAR value data type to that

Re: If condition failed

former_member209120 — Mon, 24 Jun 2013 09:18:17 GMT

Remove ' ' in between 5.5 and try

Re: If condition failed

matt — Mon, 24 Jun 2013 09:42:24 GMT

Here's some sample code. Type it into the abap editor, then do a syntax check.

DATA: v_rep type c length 80.

IF v_rep GT 4 and LT 5.5

ENDIF.

Please think before posting.

Re: If condition failed

matt — Mon, 24 Jun 2013 09:44:51 GMT

Define v_rem_f as type f. Then do v_rem_f = v_rem. Use v_rem_f for your comparison and enclose all numbers that you are comparing with in quotes.

If your data is defined as character, the system will do a character comparison - not a numeric comparison.

Re: If condition failed

thangam_perumal — Mon, 24 Jun 2013 10:25:23 GMT

Mr Ranjith,

I think data type only the problem,Please change the Data type as F and Once again do it.

Re: If condition failed

RaymondGiuseppi — Mon, 24 Jun 2013 11:23:52 GMT

Better define such constants as CONSTANTS in your program, define those with same definition as the variable you compare with, so no implicit conversion would be involved during comparison.

Regards,

Raymond

Re: If condition failed

former_member189845 — Mon, 24 Jun 2013 11:33:00 GMT

Hi Ranjith,

Plz check the below code,,

data: v_rem type c length 2 value 13.

if v_rem gt '4' and v_rem le '5.5'.
   v_rem = 432.
   else.
     IF v_rem gt 15 and v_rem le 22.
        v_rem = 111.
     ENDIF.
     endif.
write: v_rem.

if u use '4' like that den the if condition will fail. is this satisfy ur thing ?

Thx,

Siva

Re: If condition failed

matt — Mon, 24 Jun 2013 12:17:47 GMT

"Remove the quotes from '5.5'? Why don't you actually try that and see what happens. Here's some sample code. Type it into the abap editor, then do a syntax check.

DATA: v_rep type c length 80.

IF v_rep GT 4 and LT 5.5

ENDIF.

Please think before posting.

Re: If condition failed

UweFetzer_se38 — Mon, 24 Jun 2013 13:29:03 GMT

SAP is working correctly (if V_REM is really a CHAR):

"13" IS lower "4" and lower "5.5" because it starts with a "1".

Sorry, have to correct me:

"13" IS greater 4 (number conversion) but lower "5.5" because it starts with a "1".

Re: If condition failed

Former Member — Mon, 24 Jun 2013 14:05:48 GMT

Hi.

try changing 5.5 for 5,5.

Regards

Re: If condition failed

UweFetzer_se38 — Mon, 24 Jun 2013 14:22:18 GMT

Why should this work? Can you explain?