topic Re: MD_CONVERT_MATERIAL_UNIT ISSUE in Application Development and Automation Discussions

MD_CONVERT_MATERIAL_UNIT ISSUE

Former Member — Sat, 29 Jun 2013 10:28:37 GMT

Hi friends

These my requirement :

Use Function Module MD_CONVERT_MATERIAL_UNIT. Pass the following data:

I_MATNR = VBAP-MATNR

I_IN_ME= VBAP-VRKME

I_OUT_ME = “MSF”

I_MENGE = VBAP-KWMENG & Execute

Use E_MENGE

T006A-MSEHT

Pass “MSF” (UOM as described above) to T006A-MSEHI.

when i am writing the below code instead of getting conversion result iam getting kwmeng values in the output.....help me

if sy-subrc eq 0.

DATA: lv_msf LIKE mara-meins,
      lv_menge TYPE ekpo-menge.

LOOP AT git_output INTO gwa_output.

SELECT msehi
        mseht
FROM t006a
INTO TABLE git_t006a
WHERE msehi = 'MSF'.

lv_menge = gwa_output-kwmeng.

CALL FUNCTION 'MD_CONVERT_MATERIAL_UNIT'
EXPORTING
i_matnr              = gwa_output-matnr
i_in_me              = gwa_output-vrkme
i_out_me             = 'MSF'
i_menge              = lv_menge
IMPORTING
e_menge              = lv_lfimg "lv_menge
EXCEPTIONS
error_in_application = 1
error                = 2
OTHERS               = 3.

IF sy-subrc = 0.
** Implement suitable error handling here
gwa_output-kwmeng = lv_menge.
ELSE.
lv_menge = gwa_output-kwmeng.
ENDIF.
MODIFY git_output from gwa_output TRANSPORTING kwmeng.

ENDLOOP.
ENDIF.

Re: MD_CONVERT_MATERIAL_UNIT ISSUE

Former Member — Sat, 29 Jun 2013 12:35:16 GMT

Hi Naveen,

Create a variable as meshi

and call FM CONVERSION_EXIT_CUNIT_INPUT and pass MSF to it and use the variable as output parameter.

let me know if not resolved.

Regards,

Re: MD_CONVERT_MATERIAL_UNIT ISSUE

Former Member — Sat, 29 Jun 2013 12:57:40 GMT

Hi,

From your code,

lv_menge = gwa_output-kwmeng.

CALL FUNCTION 'MD_CONVERT_MATERIAL_UNIT'
EXPORTING
i_matnr              = gwa_output-matnr
i_in_me              = gwa_output-vrkme
i_out_me             = 'MSF'
i_menge              = lv_menge
IMPORTING
e_menge              = lv_lfimg "lv_menge
EXCEPTIONS
error_in_application = 1
error                = 2
OTHERS               = 3.

IF sy-subrc = 0.
** Implement suitable error handling here
gwa_output-kwmeng = lv_menge.
ELSE.
lv_menge = gwa_output-kwmeng.
ENDIF.

according to your code after calling FM, whether the sy-subrc = 0 or <> 0,the lv_menge and gwa_output-kwmeng will contain same value.

check it once .

Regards,

shamili.

Re: MD_CONVERT_MATERIAL_UNIT ISSUE

venkateswaran_k — Sat, 29 Jun 2013 13:24:40 GMT

Try in SE37 first - MD_CONVERT_MATERIAL_UNIT

By passing the value as example and verify the output value

Then debug at the place sy-subrc and see...

Probably as Shamili says, coding issue

Regards,

Venkat

Re: MD_CONVERT_MATERIAL_UNIT ISSUE

Former Member — Sat, 29 Jun 2013 17:06:05 GMT

Hi Naveen,

If you want to convert a material quantity from base to alternate or alternate to base then use FM,

'MATERIAL_UNIT_CONVERSION'.

1 thing about this FM,

*) If you want to convert an alternate unit to another alternate unit, you need to call this FM two times in sequence.

Sample Code -

*-- Set Indicator KZMEINH to indicate conversion of Alternate to Base UoM

data : lv_lfimg type lips-lfimg,

lv_meins TYPE meins,

lv_vrkme TYPE vrkme,

lv_input_qty TYPE f,

lv_output_qty TYPE f,

lv_input_qty = lv_lfimg.

lv_kzmeinh = 'X'.

CALL FUNCTION 'MATERIAL_UNIT_CONVERSION'

EXPORTING

input = lv_input_qty

kzmeinh = lv_kzmeinh

matnr = lv_matnr

meinh = lv_vrkme

meins = lv_meins

IMPORTING

output = lv_output_qty

EXCEPTIONS

conversion_not_found = 01

input_invalid = 02

material_not_found = 03

meinh_not_found = 04

meins_missing = 05

output_invalid = 06

overflow = 07.

BR.