topic plz solve my problem in Application Development and Automation Discussions

plz solve my problem

Former Member — Mon, 13 May 2013 06:40:39 GMT

hi frnds

we need to develop a report on PO release time lines.

Internal table: t_cdpos(OBJECTID FNAME CHANGENR VALUE_NEW VALUE_OLD).

After select stmt, get these values.

Row	OBJECTID	FNAME	CHANGENR	VALUE_NEW	VALUE_OLD
1	1000003	FRGZU	637324	XX	X
2	1000003	FRGZU	637323	X
3	1000003	FRGZU	637322		XX
4	1000003	FRGZU	637302	XX	X
5	1000003	FRGZU	637301	X
6	1000003	FRGZU	637300		XX
7	1000003	FRGZU	637299	XX	X
8	1000003	FRGZU	637298	X	XX
9	1000003	FRGZU	637224	XX
10	1000004	FRGZU	637223	X
11	1000004	FRGZU	637225		X
12	1000004	FRGZU	637226	X
13	1000004	FRGZU	637227	XX	X
14	1000007	FRGZU	637236	X
15	1000007	FRGZU	637237	XX	X
16	1000007	FRGZU	637238	XXX	XX
17	1000007	FRGZU	637239	XX	XXX
18	1000007	FRGZU	637240	XXX	XX
19	1000007	FRGZU	637241	XXXX	XXX

The no. of ‘X’ denotes the release against the levels of approvers found earlier. From this, the highest change doc num against each value of ‘X’, ‘XX’, ‘XXX’

i want to only for this below values.

Row	OBJECTID	FNAME	CHANGENR	VALUE_NEW	VALUE_OLD
1	1000003	FRGZU	637324	XX	X
2	1000003	FRGZU	637323	X
12	1000004	FRGZU	637226	X
13	1000004	FRGZU	637227	XX	X
14	1000007	FRGZU	637236	X
15	1000007	FRGZU	637237	XX	X
18	1000007	FRGZU	637240	XXX	XX
19	1000007	FRGZU	637241	XXXX	XXX

frnds how i can get the our requirement. any one plz help me that.

Re: plz solve my problem

RaymondGiuseppi — Mon, 13 May 2013 07:12:00 GMT

Did you try to delete from internal table records where new value is lower or equal than old value ?

Regards,

Raymond

Re: plz solve my problem

Former Member — Mon, 13 May 2013 07:20:21 GMT

Hi Kumar,

Please check the output set that you require, all you need to do is loop at the internal table and check if the VALUE_NEW GT VALUE_OLD. If this condition satisfy, append this record in final internal table.

Revert if you need more details.

Regards,

DN.

Re: plz solve my problem

Former Member — Mon, 13 May 2013 07:30:05 GMT

Hi Kumar,

Please try the below code for your requirement.

" loop for your internal table

loop at t_cdpos into wa_cdpos.

length_new = strlen( wa_cdpos-value_new ).

length_old = strlen( wa_cdpos-value_old ).

if length_new le lenght_old.

delete t_cdpos index sy-tabix.

endif.

endloop.

Thanks

Vivek

Re: plz solve my problem

Former Member — Mon, 13 May 2013 07:30:49 GMT

free the tables before you process

Re: plz solve my problem

Former Member — Mon, 13 May 2013 07:40:20 GMT

The requirement you specified is not clear can you tell if you are displaying record no 2 then why 5 and 10 is not considered . I hope you can count the length and do like this.

Delete itab where deduct is LE 0.

regards,

Rahul

Re: plz solve my problem

Former Member — Mon, 13 May 2013 08:17:14 GMT

This code will do your work.

Declare another internal table with same structure of t_cdpos,

let it be t_cdpos_fin.

data : wa_cdpos like line of t_cdpos,

wa_cdpos1 like line of t_cdpos

* Current Results

loop at t_cdpos into wa_cdpos.
   write : / wa_cdpos.
endloop.

sort t_cdpos by objectid ASCENDING value DESCENDING changenr descending.

loop at t_cdpos into wa_cdpos.

     if wa_cdpos1-value NE wa_cdpos-value and wa_cdpos-value NE ' '.
       APPEND wa_cdpos to t_cdpos_fin.
     endif.
       wa_cdpos1 = wa_cdpos.

ENDLOOP.

* Here by value I mean value_new, as i understand, only that is considered.

* Required Results

skip 3.
loop at t_cdpos_fin into wa_cdpos1.
write : /wa_cdpos1.
endloop.

Cheers,

Susmitha

Re: plz solve my problem

Former Member — Mon, 13 May 2013 09:18:31 GMT

Just to be sure, does this give the correct output?

For eg for objID 1000007, this logic would give both 637238 and 637240 as for both, new value is greater than old value. But the requirement is to get only the higher change number 637240 right?

Re: plz solve my problem

RaymondGiuseppi — Mon, 13 May 2013 09:30:40 GMT

I agree with Susmitha Thomas, my answer was only a hint to remove "rollback" records, a SORT BY OBJECTID VALUE_NEW CHANGENR DESCENDING followed by a DELETE ADJACENT DUPLICATES is required to remove duplicates keeping only last value change.

Regards,

Raymond

Re: plz solve my problem

kesavadas_thekkillath — Mon, 13 May 2013 09:35:37 GMT

Moderator message: Please use proper subject line in future. This is a kind of "do my job" post, please be sure that you mention your effort in your next question.

I recommend to read the useful Blog "Asking Good Questions in the SCN Discussion Spaces will helpyou get Good Answers" to learn the principles of asking questions.

Re: plz solve my problem

Former Member — Mon, 13 May 2013 10:04:39 GMT

This message was moderated.

Re: plz solve my problem

Former Member — Mon, 13 May 2013 12:21:23 GMT

yes,

example:

objID = 1000007

if new_value = 'X" and old_value = ' '.

suppose get multiple values, will be taken higher change value and delete low change value in table.

elseif new_value = 'XX" and old_value = 'X'.

get multiple values, will be taken highest change value and delete low change value in table.

elseif new value = 'XXX' and old_value = "XX'.

get multiple values, will be taken highest change value and delete low change value in table.

Same procedure as follow for all object ids.

objectid = 1000003.

same as above procedure.

Re: plz solve my problem

Former Member — Mon, 13 May 2013 12:48:21 GMT

Did you try the code I had posted?

Your problem is solved ?