topic Re: unable to trigger 2nd page using command in smartforms in Application Development and Automation Discussions

unable to trigger 2nd page using command in smartforms

Former Member — Sat, 04 May 2013 09:02:51 GMT

i m trying to trigger next page using command in smartform but unable to get 2nd page.

Re: unable to trigger 2nd page using command in smartforms

arindam_m — Sat, 04 May 2013 10:34:45 GMT

Hi,

Check the following tutorial. I think will make things easy.

http://www.saptechnical.com/Tutorials/Smartforms/Command/Page2.htm

Cheers,

Arindam

Re: unable to trigger 2nd page using command in smartforms

Former Member — Sat, 04 May 2013 10:46:42 GMT

Thx dude,

my scenario s tht i have creatd smartform for PO where i hav 1st page PO details & 2nd page annexure page, i hav created 2 page,but when i am trying to trigger 2nd page for annexure it is not comng.i used the command go to next page with condition set as only after end of main window.i hav inserted dis command in main window after table.

Umakant.

Re: unable to trigger 2nd page using command in smartforms

arindam_m — Sat, 04 May 2013 10:53:10 GMT

Hi,

Just to give you a heads up, The Command Node has to be a conditional trigger i.e. based on some flag that you set during processing of page 1 also the Command node in the General Attribute don't forget to check the Go to new page checkbox along with the page name.

Cheers,

Arindam

Re: unable to trigger 2nd page using command in smartforms

bastinvinoth — Sat, 04 May 2013 10:55:30 GMT

UMAKANTH KOMPELLI

You have to assign 1st Page's next page is 2nd Page and 2nd Page's next page is 2nd Page.

also create command node to call the second page hope it will solve the problem

Regards,

Bastin.G

Re: unable to trigger 2nd page using command in smartforms

Former Member — Sat, 04 May 2013 11:03:40 GMT

i hav done all the necessary setting i.e chekbox for command & in conditions clicked aftr main.

also mentioned 1st page next page as 2nd page.but no result.

--Umakant.

Re: unable to trigger 2nd page using command in smartforms

bastinvinoth — Sat, 04 May 2013 12:33:20 GMT

Can you share your smartform xml please ?

Re: unable to trigger 2nd page using command in smartforms

arindam_m — Sat, 04 May 2013 13:26:59 GMT

Hi,

In the conditions tab dont tick 'After Main' it means it will only trigger after main window processing which is not your case. Check how many entries can display in first page say for example you can display only 15 entries(depending on your layout and window size). Then after 15 entries are processed set a flag then put the condition as flag = 'X' just as shown in the example.

You can also try the following:

Insert a CODE node in the MAIN node of the table. IN that say you increment a integer value say L_COUNT to count the Loop pass. Before that Count the number of entries in table and store in Global Variable in the smartform L_NO_OF_LIN indicating number of lines in table . Increase L_COUNT by 1 before you print the line.

IF L_COUNT is GT L_NO_OF_LIN. That means last entry in the internal table in printed. SO set a flag = 'X'. Put this in the conditions tab of COMMAND node. This will trigger command after all entries are processed.

Should help you to achieve your design

Cheers,

Arindam

Re: unable to trigger 2nd page using command in smartforms

Former Member — Fri, 10 May 2013 05:33:11 GMT

thanks guys for u r reply,

i resolved prblem where i triggered 3 different command node from main window of first page and it s working fine.

Thanks,

Umakant